{"title":"IRD and power transfer units","description":"\u003cp\u003eIRD units, power transfer units, rear drive units and couplings. Check your tyres first: mismatched tyres are a leading cause of these failures.\u003c\/p\u003e","products":[{"product_id":"freelander-2-power-transfer-unit-replacement-package","title":"Freelander 2 Power Transfer Unit Replacement Package","description":"\u003cp\u003ePower Transfer Unit Replacement Package for the Freelander 2: a power transfer unit with new seals, the correct oil and fitting at our workshop.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Freelander 2 is the most common vehicle through our IRD workshop by some distance, because its power transfer unit and rear coupling are both known weak points.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 2, chassis code L359\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 3.2 i6 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2006 to 2014\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: PTU bearing and seal failure from overheated oil, which shows as a whine, a smell of hot oil and a leak at the bellhousing\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: PTU oil change at 36,000 miles thereafter, which the factory schedule omits\u003c\/li\u003e\n\u003cli\u003eTorque: PTU to gearbox 48 Nm, propshaft flange 70 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 32 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePower transfer unit\u003c\/li\u003e\n\u003cli\u003eOutput seal kit\u003c\/li\u003e\n\u003cli\u003eFill of the correct oil\u003c\/li\u003e\n\u003cli\u003ePropshaft flange bolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809433571661,"sku":"SLS-IRD-001-R","price":1399.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809433604429,"sku":"SLS-IRD-001-NU","price":1874.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_2_Power_Transfer_Unit_Replacement_Package_71d0fff5-32f7-4ac7-be57-ffb6ef1fa277.jpg?v=1790170960"},{"product_id":"range-rover-evoque-power-transfer-unit-replacement-package","title":"Range Rover Evoque Power Transfer Unit Replacement Package","description":"\u003cp\u003ePower Transfer Unit Replacement Package for the Range Rover Evoque: a power transfer unit with new seals, the correct oil and fitting at our workshop.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Evoque shares its driveline with the Freelander 2, so the power transfer unit and rear coupling faults are the same ones on a smarter car.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover Evoque, chassis code L538\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 2.0 TD4 Ingenium, 2.0 Si4 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2011 to 2018\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: PTU bearing and seal failure from overheated oil, which shows as a whine, a smell of hot oil and a leak at the bellhousing\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: PTU oil change at 36,000 miles thereafter, which the factory schedule omits\u003c\/li\u003e\n\u003cli\u003eTorque: PTU to gearbox 48 Nm, propshaft flange 70 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 32 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePower transfer unit\u003c\/li\u003e\n\u003cli\u003eOutput seal kit\u003c\/li\u003e\n\u003cli\u003eFill of the correct oil\u003c\/li\u003e\n\u003cli\u003ePropshaft flange bolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809433637197,"sku":"SLS-IRD-002-R","price":1474.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809433669965,"sku":"SLS-IRD-002-NU","price":1974.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_Evoque_Power_Transfer_Unit_Replacement_Package_bbf7c877-094f-4ca5-9628-174321554b05.jpg?v=1790170960"},{"product_id":"discovery-sport-power-transfer-unit-replacement-package","title":"Discovery Sport Power Transfer Unit Replacement Package","description":"\u003cp\u003ePower Transfer Unit Replacement Package for the Discovery Sport: a power transfer unit with new seals, the correct oil and fitting at our workshop.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Discovery Sport shares its driveline with the Evoque and the Freelander 2 family, including the power transfer unit and the rear coupling.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery Sport, chassis code L550\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 early, 2.0 TD4 Sd4 and Si4 Ingenium\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2014 on\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: PTU bearing and seal failure from overheated oil, which shows as a whine, a smell of hot oil and a leak at the bellhousing\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: PTU oil change at 36,000 miles thereafter, which the factory schedule omits\u003c\/li\u003e\n\u003cli\u003eTorque: PTU to gearbox 48 Nm, propshaft flange 70 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 32 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePower transfer unit\u003c\/li\u003e\n\u003cli\u003eOutput seal kit\u003c\/li\u003e\n\u003cli\u003eFill of the correct oil\u003c\/li\u003e\n\u003cli\u003ePropshaft flange bolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809433702733,"sku":"SLS-IRD-003-R","price":1499.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809433735501,"sku":"SLS-IRD-003-NU","price":1999.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_Sport_Power_Transfer_Unit_Replacement_Package_2b0fda3c-5501-4ee2-af92-4f1661e3c9ca.jpg?v=1790170960"},{"product_id":"freelander-2-rear-drive-unit-and-coupling-package","title":"Freelander 2 Rear Drive Unit and Coupling Package","description":"\u003cp\u003eRear Drive Unit and Coupling Package for the Freelander 2: the rear differential with the Haldex coupling, pump and filter, fitted and calibrated.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Freelander 2 is the most common vehicle through our IRD workshop by some distance, because its power transfer unit and rear coupling are both known weak points.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 2, chassis code L359\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 3.2 i6 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2006 to 2014\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: rear coupling pump failure that leaves the vehicle quietly front wheel drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: coupling oil and filter every 36,000 miles\u003c\/li\u003e\n\u003cli\u003eTorque: RDU mounts 115 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 36 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eCoupling pump and filter\u003c\/li\u003e\n\u003cli\u003eOil fill\u003c\/li\u003e\n\u003cli\u003eMount bolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809433768269,"sku":"SLS-IRD-004-R","price":1599.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809433801037,"sku":"SLS-IRD-004-NU","price":2124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_2_Rear_Drive_Unit_and_Coupling_Package_d7ce576a-700f-4b60-907d-c786f31c92f9.jpg?v=1790170960"},{"product_id":"range-rover-evoque-rear-drive-unit-and-coupling-package","title":"Range Rover Evoque Rear Drive Unit and Coupling Package","description":"\u003cp\u003eRear Drive Unit and Coupling Package for the Range Rover Evoque: the rear differential with the Haldex coupling, pump and filter, fitted and calibrated.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Evoque shares its driveline with the Freelander 2, so the power transfer unit and rear coupling faults are the same ones on a smarter car.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover Evoque, chassis code L538\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 2.0 TD4 Ingenium, 2.0 Si4 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2011 to 2018\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: rear coupling pump failure that leaves the vehicle quietly front wheel drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: coupling oil and filter every 36,000 miles\u003c\/li\u003e\n\u003cli\u003eTorque: RDU mounts 115 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 36 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eCoupling pump and filter\u003c\/li\u003e\n\u003cli\u003eOil fill\u003c\/li\u003e\n\u003cli\u003eMount bolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809433833805,"sku":"SLS-IRD-005-R","price":1649.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809433866573,"sku":"SLS-IRD-005-NU","price":2224.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_Evoque_Rear_Drive_Unit_and_Coupling_Package_82fb3033-b35c-454e-8b58-24de0162fa4f.jpg?v=1790170960"},{"product_id":"discovery-sport-rear-drive-unit-and-coupling-package","title":"Discovery Sport Rear Drive Unit and Coupling Package","description":"\u003cp\u003eRear Drive Unit and Coupling Package for the Discovery Sport: the rear differential with the Haldex coupling, pump and filter, fitted and calibrated.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Discovery Sport shares its driveline with the Evoque and the Freelander 2 family, including the power transfer unit and the rear coupling.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery Sport, chassis code L550\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 early, 2.0 TD4 Sd4 and Si4 Ingenium\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2014 on\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: rear coupling pump failure that leaves the vehicle quietly front wheel drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: coupling oil and filter every 36,000 miles\u003c\/li\u003e\n\u003cli\u003eTorque: RDU mounts 115 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 36 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eCoupling pump and filter\u003c\/li\u003e\n\u003cli\u003eOil fill\u003c\/li\u003e\n\u003cli\u003eMount bolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809433899341,"sku":"SLS-IRD-006-R","price":1699.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809433932109,"sku":"SLS-IRD-006-NU","price":2274.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_Sport_Rear_Drive_Unit_and_Coupling_Package_8a97666e-8fd8-44cb-ac5b-79cbff8a913c.jpg?v=1790170960"},{"product_id":"freelander-2-complete-driveline-overhaul","title":"Freelander 2 Complete Driveline Overhaul","description":"\u003cp\u003eComplete Driveline Overhaul for the Freelander 2: the transfer unit, propshaft, rear drive unit and every driveline oil, done once and done together.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Freelander 2 is the most common vehicle through our IRD workshop by some distance, because its power transfer unit and rear coupling are both known weak points.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 2, chassis code L359\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 3.2 i6 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2006 to 2014\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the chain of driveline failures that follows one worn unit on these vehicles\u003c\/li\u003e\n\u003cli\u003eLabour time: about 9 hours\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: four matching tyres\u003c\/li\u003e\n\u003cli\u003eTorque: to factory figures, supplied\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: three years or 36,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTransfer unit\u003c\/li\u003e\n\u003cli\u003ePropshaft with new bearings\u003c\/li\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eAll driveline oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 9 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809433964877,"sku":"SLS-IRD-007-PO","price":2449.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809433997645,"sku":"SLS-IRD-007-PAF","price":3124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_2_Complete_Driveline_Overhaul_5c1aa29a-ac34-4cd0-b8b4-9e7076dae4e6.jpg?v=1790170960"},{"product_id":"range-rover-evoque-complete-driveline-overhaul","title":"Range Rover Evoque Complete Driveline Overhaul","description":"\u003cp\u003eComplete Driveline Overhaul for the Range Rover Evoque: the transfer unit, propshaft, rear drive unit and every driveline oil, done once and done together.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Evoque shares its driveline with the Freelander 2, so the power transfer unit and rear coupling faults are the same ones on a smarter car.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover Evoque, chassis code L538\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 2.0 TD4 Ingenium, 2.0 Si4 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2011 to 2018\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the chain of driveline failures that follows one worn unit on these vehicles\u003c\/li\u003e\n\u003cli\u003eLabour time: about 9 hours\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: four matching tyres\u003c\/li\u003e\n\u003cli\u003eTorque: to factory figures, supplied\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: three years or 36,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTransfer unit\u003c\/li\u003e\n\u003cli\u003ePropshaft with new bearings\u003c\/li\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eAll driveline oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 9 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809434030413,"sku":"SLS-IRD-008-PO","price":2549.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809434063181,"sku":"SLS-IRD-008-PAF","price":3249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_Evoque_Complete_Driveline_Overhaul_35f15c51-b724-4a91-b822-fe8ffc417ab1.jpg?v=1790170960"},{"product_id":"discovery-sport-complete-driveline-overhaul","title":"Discovery Sport Complete Driveline Overhaul","description":"\u003cp\u003eComplete Driveline Overhaul for the Discovery Sport: the transfer unit, propshaft, rear drive unit and every driveline oil, done once and done together.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Discovery Sport shares its driveline with the Evoque and the Freelander 2 family, including the power transfer unit and the rear coupling.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery Sport, chassis code L550\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 early, 2.0 TD4 Sd4 and Si4 Ingenium\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2014 on\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the chain of driveline failures that follows one worn unit on these vehicles\u003c\/li\u003e\n\u003cli\u003eLabour time: about 9 hours\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: four matching tyres\u003c\/li\u003e\n\u003cli\u003eTorque: to factory figures, supplied\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: three years or 36,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTransfer unit\u003c\/li\u003e\n\u003cli\u003ePropshaft with new bearings\u003c\/li\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eAll driveline oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 9 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809434095949,"sku":"SLS-IRD-009-PO","price":2599.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809434128717,"sku":"SLS-IRD-009-PAF","price":3324.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_Sport_Complete_Driveline_Overhaul_55dd4c77-2859-4d45-a1da-02a0cf9bd832.jpg?v=1790170961"},{"product_id":"freelander-1-complete-driveline-overhaul","title":"Freelander 1 Complete Driveline Overhaul","description":"\u003cp\u003eComplete Driveline Overhaul for the Freelander 1: the transfer unit, propshaft, rear drive unit and every driveline oil, done once and done together.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Freelander 1 runs an IRD, a viscous coupling and a rear diff in one line, and all three live or die by whether the four tyres match.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 1, chassis code L314\u003c\/li\u003e\n\u003cli\u003eEngine: 1.8 K Series, 2.0 L Series and Td4 diesel, 2.5 KV6\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1997 to 2006\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the chain of driveline failures that follows one worn unit on these vehicles\u003c\/li\u003e\n\u003cli\u003eLabour time: about 9 hours\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: four matching tyres\u003c\/li\u003e\n\u003cli\u003eTorque: to factory figures, supplied\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: three years or 36,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTransfer unit\u003c\/li\u003e\n\u003cli\u003ePropshaft with new bearings\u003c\/li\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eAll driveline oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 9 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809434161485,"sku":"SLS-IRD-010-PO","price":2124.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809434194253,"sku":"SLS-IRD-010-PAF","price":2724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_1_Complete_Driveline_Overhaul_f8c8f15d-8309-40e7-bedb-132568bb1905.jpg?v=1790170961"},{"product_id":"freelander-1-ird-unit-exchange","title":"Freelander 1 IRD Unit Exchange","description":"\u003cp\u003eIRD Unit Exchange for the Freelander 1: a remanufactured IRD on an exchange basis, supplied ready to fit.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Freelander 1 runs an IRD, a viscous coupling and a rear diff in one line, and all three live or die by whether the four tyres match.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 1, chassis code L314\u003c\/li\u003e\n\u003cli\u003eEngine: 1.8 K Series, 2.0 L Series and Td4 diesel, 2.5 KV6\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1997 to 2006\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: IRD bearing and gear failure after viscous coupling seizure\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a new viscous coupling if yours is stiff, which it probably is\u003c\/li\u003e\n\u003cli\u003eTorque: 45 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 22 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRemanufactured IRD\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eCore return label\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809434227021,"sku":"SLS-IRD-011-R","price":449.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809434259789,"sku":"SLS-IRD-011-NU","price":599.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_1_IRD_Unit_Exchange_a0bee324-9e6d-4fa0-9a35-b58be2f7e44f.jpg?v=1790170960"},{"product_id":"freelander-1-viscous-coupling-unit","title":"Freelander 1 Viscous Coupling Unit","description":"\u003cp\u003eViscous Coupling Unit for the Freelander 1: the viscous coupling that sits in the propshaft line and dies when the tyres do not match.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Freelander 1 runs an IRD, a viscous coupling and a rear diff in one line, and all three live or die by whether the four tyres match.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 1, chassis code L314\u003c\/li\u003e\n\u003cli\u003eEngine: 1.8 K Series, 2.0 L Series and Td4 diesel, 2.5 KV6\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1997 to 2006\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: stiff or seized VCU, the root cause of most Freelander 1 IRD failures\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: propshaft bearings\u003c\/li\u003e\n\u003cli\u003eTorque: propshaft flange 45 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 7 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eViscous coupling unit\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809434292557,"sku":"SLS-DRV-001-OS","price":229.0,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809434325325,"sku":"SLS-DRV-001-PA","price":179.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_1_Viscous_Coupling_Unit_c6746323-3aa4-4e3e-ace5-f1b976766618.jpg?v=1790170961"},{"product_id":"freelander-2-power-transfer-unit","title":"Freelander 2 Power Transfer Unit","description":"\u003cp\u003ePower Transfer Unit for the Freelander 2: a power transfer unit supplied for your garage to fit.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Freelander 2 is the most common vehicle through our IRD workshop by some distance, because its power transfer unit and rear coupling are both known weak points.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 2, chassis code L359\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 3.2 i6 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2006 to 2014\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: PTU bearing and seal failure\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: the correct PTU oil\u003c\/li\u003e\n\u003cli\u003eTorque: 48 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 21 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePower transfer unit\u003c\/li\u003e\n\u003cli\u003eSeal kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809434358093,"sku":"SLS-IRD-012-R","price":839.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809434390861,"sku":"SLS-IRD-012-NU","price":1124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_2_Power_Transfer_Unit_695ffb72-a335-4a05-89c0-4abbc2a02465.jpg?v=1790170961"},{"product_id":"range-rover-evoque-power-transfer-unit","title":"Range Rover Evoque Power Transfer Unit","description":"\u003cp\u003ePower Transfer Unit for the Range Rover Evoque: a power transfer unit supplied for your garage to fit.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Evoque shares its driveline with the Freelander 2, so the power transfer unit and rear coupling faults are the same ones on a smarter car.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover Evoque, chassis code L538\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 2.0 TD4 Ingenium, 2.0 Si4 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2011 to 2018\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: PTU bearing and seal failure\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: the correct PTU oil\u003c\/li\u003e\n\u003cli\u003eTorque: 48 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 21 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePower transfer unit\u003c\/li\u003e\n\u003cli\u003eSeal kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809434554701,"sku":"SLS-IRD-013-R","price":879.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809434587469,"sku":"SLS-IRD-013-NU","price":1174.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_Evoque_Power_Transfer_Unit_e526ee8c-33e6-4d23-a227-09e0cea71964.jpg?v=1790170961"},{"product_id":"discovery-sport-power-transfer-unit","title":"Discovery Sport Power Transfer Unit","description":"\u003cp\u003ePower Transfer Unit for the Discovery Sport: a power transfer unit supplied for your garage to fit.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Discovery Sport shares its driveline with the Evoque and the Freelander 2 family, including the power transfer unit and the rear coupling.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery Sport, chassis code L550\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 early, 2.0 TD4 Sd4 and Si4 Ingenium\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2014 on\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: PTU bearing and seal failure\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: the correct PTU oil\u003c\/li\u003e\n\u003cli\u003eTorque: 48 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 21 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePower transfer unit\u003c\/li\u003e\n\u003cli\u003eSeal kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809434685773,"sku":"SLS-IRD-014-R","price":899.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809434718541,"sku":"SLS-IRD-014-NU","price":1199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_Sport_Power_Transfer_Unit_ea2043bb-53ac-48bf-9e5b-1f9fdcab46fd.jpg?v=1790170961"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/collections\/hf_20260923_135804_94347f51-7fe3-4f5f-8666-52a62ce9bde1.png?v=1790172093","url":"https:\/\/solihullspares.com\/collections\/ird.oembed","provider":"Solihull Spares","version":"1.0","type":"link"}