{"title":"Driveline, steering and hubs","description":"\u003cp\u003ePropshafts, universal joints, swivel housings, wheel bearings, track rods, steering dampers and racks.\u003c\/p\u003e","products":[{"product_id":"freelander-2-complete-driveline-overhaul","title":"Freelander 2 Complete Driveline Overhaul","description":"\u003cp\u003eComplete Driveline Overhaul for the Freelander 2: the transfer unit, propshaft, rear drive unit and every driveline oil, done once and done together.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Freelander 2 is the most common vehicle through our IRD workshop by some distance, because its power transfer unit and rear coupling are both known weak points.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 2, chassis code L359\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 3.2 i6 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2006 to 2014\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the chain of driveline failures that follows one worn unit on these vehicles\u003c\/li\u003e\n\u003cli\u003eLabour time: about 9 hours\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: four matching tyres\u003c\/li\u003e\n\u003cli\u003eTorque: to factory figures, supplied\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: three years or 36,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTransfer unit\u003c\/li\u003e\n\u003cli\u003ePropshaft with new bearings\u003c\/li\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eAll driveline oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 9 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809433964877,"sku":"SLS-IRD-007-PO","price":2449.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809433997645,"sku":"SLS-IRD-007-PAF","price":3124.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_2_Complete_Driveline_Overhaul_5c1aa29a-ac34-4cd0-b8b4-9e7076dae4e6.jpg?v=1790170960"},{"product_id":"range-rover-evoque-complete-driveline-overhaul","title":"Range Rover Evoque Complete Driveline Overhaul","description":"\u003cp\u003eComplete Driveline Overhaul for the Range Rover Evoque: the transfer unit, propshaft, rear drive unit and every driveline oil, done once and done together.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Evoque shares its driveline with the Freelander 2, so the power transfer unit and rear coupling faults are the same ones on a smarter car.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover Evoque, chassis code L538\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 2.0 TD4 Ingenium, 2.0 Si4 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2011 to 2018\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the chain of driveline failures that follows one worn unit on these vehicles\u003c\/li\u003e\n\u003cli\u003eLabour time: about 9 hours\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: four matching tyres\u003c\/li\u003e\n\u003cli\u003eTorque: to factory figures, supplied\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: three years or 36,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTransfer unit\u003c\/li\u003e\n\u003cli\u003ePropshaft with new bearings\u003c\/li\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eAll driveline oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 9 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809434030413,"sku":"SLS-IRD-008-PO","price":2549.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809434063181,"sku":"SLS-IRD-008-PAF","price":3249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_Evoque_Complete_Driveline_Overhaul_35f15c51-b724-4a91-b822-fe8ffc417ab1.jpg?v=1790170960"},{"product_id":"discovery-sport-complete-driveline-overhaul","title":"Discovery Sport Complete Driveline Overhaul","description":"\u003cp\u003eComplete Driveline Overhaul for the Discovery Sport: the transfer unit, propshaft, rear drive unit and every driveline oil, done once and done together.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Discovery Sport shares its driveline with the Evoque and the Freelander 2 family, including the power transfer unit and the rear coupling.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery Sport, chassis code L550\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 early, 2.0 TD4 Sd4 and Si4 Ingenium\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2014 on\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the chain of driveline failures that follows one worn unit on these vehicles\u003c\/li\u003e\n\u003cli\u003eLabour time: about 9 hours\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: four matching tyres\u003c\/li\u003e\n\u003cli\u003eTorque: to factory figures, supplied\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: three years or 36,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTransfer unit\u003c\/li\u003e\n\u003cli\u003ePropshaft with new bearings\u003c\/li\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eAll driveline oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 9 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809434095949,"sku":"SLS-IRD-009-PO","price":2599.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809434128717,"sku":"SLS-IRD-009-PAF","price":3324.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_Sport_Complete_Driveline_Overhaul_55dd4c77-2859-4d45-a1da-02a0cf9bd832.jpg?v=1790170961"},{"product_id":"freelander-1-complete-driveline-overhaul","title":"Freelander 1 Complete Driveline Overhaul","description":"\u003cp\u003eComplete Driveline Overhaul for the Freelander 1: the transfer unit, propshaft, rear drive unit and every driveline oil, done once and done together.\u003c\/p\u003e\u003cp\u003eThe IRD, or power transfer unit on the later cars, takes drive from the gearbox to the propshaft. On the Freelander 1 it fails because the viscous coupling in the propshaft line seizes and fights it, and the commonest cause of that is one tyre different from the other three. On the Freelander 2, Evoque and Discovery Sport the unit runs hot, the oil breaks down, and the bearings and seals go. Every unit here comes with the advice that stops it happening again, which is four matching tyres at matching pressures and an oil change the factory schedule does not ask for. The Freelander 1 runs an IRD, a viscous coupling and a rear diff in one line, and all three live or die by whether the four tyres match.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 1, chassis code L314\u003c\/li\u003e\n\u003cli\u003eEngine: 1.8 K Series, 2.0 L Series and Td4 diesel, 2.5 KV6\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1997 to 2006\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the chain of driveline failures that follows one worn unit on these vehicles\u003c\/li\u003e\n\u003cli\u003eLabour time: about 9 hours\u003c\/li\u003e\n\u003cli\u003eCoding: a calibration or adaptation routine is required afterwards with a dealer level diagnostic system; a generic code reader cannot do it\u003c\/li\u003e\n\u003cli\u003eAlso needed: four matching tyres\u003c\/li\u003e\n\u003cli\u003eTorque: to factory figures, supplied\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: three years or 36,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTransfer unit\u003c\/li\u003e\n\u003cli\u003ePropshaft with new bearings\u003c\/li\u003e\n\u003cli\u003eRear drive unit\u003c\/li\u003e\n\u003cli\u003eAll driveline oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 9 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809434161485,"sku":"SLS-IRD-010-PO","price":2124.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809434194253,"sku":"SLS-IRD-010-PAF","price":2724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_1_Complete_Driveline_Overhaul_f8c8f15d-8309-40e7-bedb-132568bb1905.jpg?v=1790170961"},{"product_id":"defender-90-heavy-duty-half-shaft-pair","title":"Defender 90 Heavy Duty Half Shaft Pair","description":"\u003cp\u003eHeavy Duty Half Shaft Pair for the Defender 90: a pair of heavy duty half shafts in a stronger alloy.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 90 is the short wheelbase and the one that gets used hardest off road, so the parts on it are the ones we see worn out fastest.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 90, chassis code LD 90\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shafts twisted or snapped at the spline off road\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub oil seals\u003c\/li\u003e\n\u003cli\u003eTorque: drive flange 65 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 16 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eTwo half shafts\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809447858509,"sku":"SLS-DRV-005-S","price":399.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809447891277,"sku":"SLS-DRV-005-HD","price":469.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_90_Heavy_Duty_Half_Shaft_Pair_1e092660-a3fa-49f8-af3b-915521062072.jpg?v=1790171062"},{"product_id":"defender-110-heavy-duty-half-shaft-pair","title":"Defender 110 Heavy Duty Half Shaft Pair","description":"\u003cp\u003eHeavy Duty Half Shaft Pair for the Defender 110: a pair of heavy duty half shafts in a stronger alloy.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 110 is the working Defender: farms, estates, utilities and expeditions, usually loaded and usually towing.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 110, chassis code LD 110\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shafts twisted or snapped at the spline off road\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub oil seals\u003c\/li\u003e\n\u003cli\u003eTorque: drive flange 65 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 16 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eTwo half shafts\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809447924045,"sku":"SLS-DRV-006-S","price":419.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809447956813,"sku":"SLS-DRV-006-HD","price":499.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_110_Heavy_Duty_Half_Shaft_Pair_6335f539-980d-4318-9f00-e0f1ab14a233.jpg?v=1790171062"},{"product_id":"defender-130-heavy-duty-half-shaft-pair","title":"Defender 130 Heavy Duty Half Shaft Pair","description":"\u003cp\u003eHeavy Duty Half Shaft Pair for the Defender 130: a pair of heavy duty half shafts in a stronger alloy.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 130 is the long wheelbase crew cab and pick up, and it carries its weight on the rear axle, which changes which parts wear first.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 130, chassis code LD 130\u003c\/li\u003e\n\u003cli\u003eEngine: 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1984 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shafts twisted or snapped at the spline off road\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub oil seals\u003c\/li\u003e\n\u003cli\u003eTorque: drive flange 65 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 16 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eTwo half shafts\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809447989581,"sku":"SLS-DRV-007-S","price":439.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809448022349,"sku":"SLS-DRV-007-HD","price":529.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_130_Heavy_Duty_Half_Shaft_Pair_2c69525f-8e71-4769-b8bf-f62b857835b4.jpg?v=1790171062"},{"product_id":"discovery-1-heavy-duty-half-shaft-pair","title":"Discovery 1 Heavy Duty Half Shaft Pair","description":"\u003cp\u003eHeavy Duty Half Shaft Pair for the Discovery 1: a pair of heavy duty half shafts in a stronger alloy.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shafts twisted or snapped at the spline off road\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub oil seals\u003c\/li\u003e\n\u003cli\u003eTorque: drive flange 65 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 16 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eTwo half shafts\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809448055117,"sku":"SLS-DRV-008-S","price":379.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809448087885,"sku":"SLS-DRV-008-HD","price":459.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Heavy_Duty_Half_Shaft_Pair_603136df-d495-4f8d-a313-b230f23821a0.jpg?v=1790171062"},{"product_id":"discovery-2-heavy-duty-half-shaft-pair","title":"Discovery 2 Heavy Duty Half Shaft Pair","description":"\u003cp\u003eHeavy Duty Half Shaft Pair for the Discovery 2: a pair of heavy duty half shafts in a stronger alloy.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shafts twisted or snapped at the spline off road\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub oil seals\u003c\/li\u003e\n\u003cli\u003eTorque: drive flange 65 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 16 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eTwo half shafts\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809448186189,"sku":"SLS-DRV-009-S","price":399.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809448218957,"sku":"SLS-DRV-009-HD","price":469.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Heavy_Duty_Half_Shaft_Pair_3f4db813-68f9-4b06-83f3-511ad7c20bd0.jpg?v=1790171062"},{"product_id":"defender-90-swivel-housing-rebuild-kit","title":"Defender 90 Swivel Housing Rebuild Kit","description":"\u003cp\u003eSwivel Housing Rebuild Kit for the Defender 90: a new chrome swivel ball, bearings, seals and gaskets for one side.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 90 is the short wheelbase and the one that gets used hardest off road, so the parts on it are the ones we see worn out fastest.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 90, chassis code LD 90\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: pitted chrome tearing the seal and leaking oil down the wheel\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: swivel oil or grease\u003c\/li\u003e\n\u003cli\u003eTorque: swivel to axle 73 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSwivel ball\u003c\/li\u003e\n\u003cli\u003eTaper bearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809489146189,"sku":"SLS-SWV-001-OS","price":194.95,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809489178957,"sku":"SLS-SWV-001-U","price":239.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809489211725,"sku":"SLS-SWV-001-GB","price":279.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_90_Swivel_Housing_Rebuild_Kit_6b1fbf0c-e13a-426a-9785-db69470bacdc.jpg?v=1790171315"},{"product_id":"defender-110-swivel-housing-rebuild-kit","title":"Defender 110 Swivel Housing Rebuild Kit","description":"\u003cp\u003eSwivel Housing Rebuild Kit for the Defender 110: a new chrome swivel ball, bearings, seals and gaskets for one side.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 110 is the working Defender: farms, estates, utilities and expeditions, usually loaded and usually towing.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 110, chassis code LD 110\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: pitted chrome tearing the seal and leaking oil down the wheel\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: swivel oil or grease\u003c\/li\u003e\n\u003cli\u003eTorque: swivel to axle 73 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSwivel ball\u003c\/li\u003e\n\u003cli\u003eTaper bearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809489703245,"sku":"SLS-SWV-002-OS","price":209.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809489736013,"sku":"SLS-SWV-002-U","price":249.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809489768781,"sku":"SLS-SWV-002-GB","price":289.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_110_Swivel_Housing_Rebuild_Kit_e62e7eea-b358-4a5a-be67-6dbdb0a653a8.jpg?v=1790171315"},{"product_id":"defender-130-swivel-housing-rebuild-kit","title":"Defender 130 Swivel Housing Rebuild Kit","description":"\u003cp\u003eSwivel Housing Rebuild Kit for the Defender 130: a new chrome swivel ball, bearings, seals and gaskets for one side.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 130 is the long wheelbase crew cab and pick up, and it carries its weight on the rear axle, which changes which parts wear first.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 130, chassis code LD 130\u003c\/li\u003e\n\u003cli\u003eEngine: 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1984 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: pitted chrome tearing the seal and leaking oil down the wheel\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: swivel oil or grease\u003c\/li\u003e\n\u003cli\u003eTorque: swivel to axle 73 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSwivel ball\u003c\/li\u003e\n\u003cli\u003eTaper bearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809489867085,"sku":"SLS-SWV-003-OS","price":219.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809489899853,"sku":"SLS-SWV-003-U","price":269.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809489932621,"sku":"SLS-SWV-003-GB","price":309.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_130_Swivel_Housing_Rebuild_Kit_a3efebe2-94b0-4837-b701-5366b1a15415.jpg?v=1790171315"},{"product_id":"discovery-1-swivel-housing-rebuild-kit","title":"Discovery 1 Swivel Housing Rebuild Kit","description":"\u003cp\u003eSwivel Housing Rebuild Kit for the Discovery 1: a new chrome swivel ball, bearings, seals and gaskets for one side.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: pitted chrome tearing the seal and leaking oil down the wheel\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: swivel oil or grease\u003c\/li\u003e\n\u003cli\u003eTorque: swivel to axle 73 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSwivel ball\u003c\/li\u003e\n\u003cli\u003eTaper bearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809490096461,"sku":"SLS-SWV-004-OS","price":184.95,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809490129229,"sku":"SLS-SWV-004-U","price":229.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809490161997,"sku":"SLS-SWV-004-GB","price":269.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Swivel_Housing_Rebuild_Kit_1ab9b0f3-f322-4aff-8db6-bd1647e66c54.jpg?v=1790171315"},{"product_id":"discovery-2-swivel-housing-rebuild-kit","title":"Discovery 2 Swivel Housing Rebuild Kit","description":"\u003cp\u003eSwivel Housing Rebuild Kit for the Discovery 2: a new chrome swivel ball, bearings, seals and gaskets for one side.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: pitted chrome tearing the seal and leaking oil down the wheel\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: swivel oil or grease\u003c\/li\u003e\n\u003cli\u003eTorque: swivel to axle 73 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSwivel ball\u003c\/li\u003e\n\u003cli\u003eTaper bearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809490260301,"sku":"SLS-SWV-005-OS","price":194.95,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809490293069,"sku":"SLS-SWV-005-U","price":239.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809490325837,"sku":"SLS-SWV-005-GB","price":279.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Swivel_Housing_Rebuild_Kit_db7fc93c-6916-4da3-92d0-79c20ec974c7.jpg?v=1790171315"},{"product_id":"defender-90-wheel-bearing-kit","title":"Defender 90 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Defender 90: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 90 is the short wheelbase and the one that gets used hardest off road, so the parts on it are the ones we see worn out fastest.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 90, chassis code LD 90\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809490620749,"sku":"SLS-SWV-006-OS","price":84.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809490653517,"sku":"SLS-SWV-006-GB","price":119.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809490686285,"sku":"SLS-SWV-006-PA","price":64.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_90_Wheel_Bearing_Kit_c1f34a92-7a8a-434f-b92c-66f95b29a02a.jpg?v=1790171316"},{"product_id":"defender-110-wheel-bearing-kit","title":"Defender 110 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Defender 110: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 110 is the working Defender: farms, estates, utilities and expeditions, usually loaded and usually towing.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 110, chassis code LD 110\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809490784589,"sku":"SLS-SWV-007-OS","price":89.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809490817357,"sku":"SLS-SWV-007-GB","price":129.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809490850125,"sku":"SLS-SWV-007-PA","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_110_Wheel_Bearing_Kit_233b8aaa-467e-479e-a5f9-e6a8824ab1b9.jpg?v=1790171315"},{"product_id":"defender-130-wheel-bearing-kit","title":"Defender 130 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Defender 130: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 130 is the long wheelbase crew cab and pick up, and it carries its weight on the rear axle, which changes which parts wear first.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 130, chassis code LD 130\u003c\/li\u003e\n\u003cli\u003eEngine: 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1984 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809491046733,"sku":"SLS-SWV-008-OS","price":94.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809491079501,"sku":"SLS-SWV-008-GB","price":134.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809491112269,"sku":"SLS-SWV-008-PA","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_130_Wheel_Bearing_Kit_faa7522c-d385-415f-b1c7-8a0db6e57141.jpg?v=1790171315"},{"product_id":"discovery-1-wheel-bearing-kit","title":"Discovery 1 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Discovery 1: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809491407181,"sku":"SLS-SWV-009-OS","price":79.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809491439949,"sku":"SLS-SWV-009-GB","price":114.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809491472717,"sku":"SLS-SWV-009-PA","price":59.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Wheel_Bearing_Kit_ece8f1dd-becc-4b46-9462-c4ea4a5bc1c4.jpg?v=1790171316"},{"product_id":"discovery-2-wheel-bearing-kit","title":"Discovery 2 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Discovery 2: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809491636557,"sku":"SLS-SWV-010-OS","price":84.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809491669325,"sku":"SLS-SWV-010-GB","price":119.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809491702093,"sku":"SLS-SWV-010-PA","price":64.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Wheel_Bearing_Kit_ab0839d5-06a7-4960-b4e1-e64380483ccc.jpg?v=1790171316"},{"product_id":"discovery-3-wheel-bearing-kit","title":"Discovery 3 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Discovery 3: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 3 was the first on the integrated body frame and the first with full air suspension as standard, which is where most of its bills come from.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 3, chassis code L319\u003c\/li\u003e\n\u003cli\u003eEngine: 2.7 TDV6 diesel and 4.4 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2004 to 2009\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809491800397,"sku":"SLS-SWV-011-OS","price":89.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809491833165,"sku":"SLS-SWV-011-GB","price":129.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809491865933,"sku":"SLS-SWV-011-PA","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_3_Wheel_Bearing_Kit_56015e2e-6da6-4dc5-aa33-a6c1eb8d61cc.jpg?v=1790171316"},{"product_id":"discovery-4-wheel-bearing-kit","title":"Discovery 4 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Discovery 4: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 4 is the Discovery 3 made better, but the 3.0 V6 diesel carries a crankshaft failure risk that every owner ought to know about.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 4, chassis code L319\u003c\/li\u003e\n\u003cli\u003eEngine: 3.0 TDV6 and SDV6 diesel, 5.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2009 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809491997005,"sku":"SLS-SWV-012-OS","price":94.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809492029773,"sku":"SLS-SWV-012-GB","price":134.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809492062541,"sku":"SLS-SWV-012-PA","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_4_Wheel_Bearing_Kit_860f4ab2-e37f-4498-830a-446a94d14702.jpg?v=1790171316"},{"product_id":"discovery-5-wheel-bearing-kit","title":"Discovery 5 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Discovery 5: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 5 is aluminium bodied and largely Ingenium powered, and it still runs air suspension and a two speed transfer box on most specifications.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 5, chassis code L462\u003c\/li\u003e\n\u003cli\u003eEngine: 2.0 Sd4 and Si4 Ingenium, 3.0 TDV6 and SDV6, D250 and D300\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2017 on\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809492521293,"sku":"SLS-SWV-013-OS","price":99.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809492554061,"sku":"SLS-SWV-013-GB","price":139.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809492586829,"sku":"SLS-SWV-013-PA","price":74.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_5_Wheel_Bearing_Kit_938213eb-4166-4198-819b-451b6161e0af.jpg?v=1790171316"},{"product_id":"range-rover-sport-l320-wheel-bearing-kit","title":"Range Rover Sport L320 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Range Rover Sport L320: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Sport L320 sits on the Discovery 3 and 4 frame with the same air suspension, the same transfer box and the same diesel engines.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover Sport L320, chassis code L320\u003c\/li\u003e\n\u003cli\u003eEngine: 2.7 and 3.0 TDV6, 3.0 SDV6, 3.6 TDV8 diesel, 4.2 and 5.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2005 to 2013\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809492783437,"sku":"SLS-SWV-014-OS","price":89.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809492816205,"sku":"SLS-SWV-014-GB","price":129.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809492848973,"sku":"SLS-SWV-014-PA","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_Sport_L320_Wheel_Bearing_Kit_0cb6b727-1c30-44c5-97bb-4a6297e8ad61.jpg?v=1790171316"},{"product_id":"range-rover-sport-l494-wheel-bearing-kit","title":"Range Rover Sport L494 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Range Rover Sport L494: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Sport L494 is the aluminium Sport, sharing most of its hardware with the L405 in a shorter body.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover Sport L494, chassis code L494\u003c\/li\u003e\n\u003cli\u003eEngine: 3.0 TDV6 and SDV6, 4.4 SDV8 diesel, 5.0 V8, P400e\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2013 to 2022\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809492980045,"sku":"SLS-SWV-015-OS","price":99.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809493012813,"sku":"SLS-SWV-015-GB","price":144.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809493045581,"sku":"SLS-SWV-015-PA","price":79.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_Sport_L494_Wheel_Bearing_Kit_da0b4f43-994a-4ff9-a291-d3525e118515.jpg?v=1790171316"},{"product_id":"range-rover-l322-wheel-bearing-kit","title":"Range Rover L322 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Range Rover L322: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The L322 is the Range Rover that most people can now afford to buy and not all can afford to run, which is exactly why honest parts prices matter on it.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover L322, chassis code L322\u003c\/li\u003e\n\u003cli\u003eEngine: Td6, 3.6 and 4.4 TDV8 diesel, 4.4 and 4.2 V8, 5.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2002 to 2012\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809493340493,"sku":"SLS-SWV-016-OS","price":94.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809493373261,"sku":"SLS-SWV-016-GB","price":139.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809493406029,"sku":"SLS-SWV-016-PA","price":74.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_L322_Wheel_Bearing_Kit_2ddb689f-4056-42fc-803c-77b1ba81a65d.jpg?v=1790171316"},{"product_id":"range-rover-l405-wheel-bearing-kit","title":"Range Rover L405 Wheel Bearing Kit","description":"\u003cp\u003eWheel Bearing Kit for the Range Rover L405: a wheel bearing kit for one hub with seals and a new nut.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The L405 is aluminium bodied with four corner air suspension and adaptive dampers, and its parts are dearer than the earlier cars for good reasons.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover L405, chassis code L405\u003c\/li\u003e\n\u003cli\u003eEngine: 3.0 TDV6 and SDV6, 4.4 SDV8 diesel, 5.0 V8, P400e\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2012 to 2021\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rumble that changes with road speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub grease\u003c\/li\u003e\n\u003cli\u003eTorque: hub nut to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2.5 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003cli\u003eSeals\u003c\/li\u003e\n\u003cli\u003eNut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809493569869,"sku":"SLS-SWV-017-OS","price":104.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809493602637,"sku":"SLS-SWV-017-GB","price":149.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809493635405,"sku":"SLS-SWV-017-PA","price":79.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_L405_Wheel_Bearing_Kit_2e90bdc7-1ffc-41cc-9278-5b3f85059db9.jpg?v=1790171316"},{"product_id":"defender-90-steering-damper","title":"Defender 90 Steering Damper","description":"\u003cp\u003eSteering Damper for the Defender 90: a steering damper to calm wheel shimmy.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 90 is the short wheelbase and the one that gets used hardest off road, so the parts on it are the ones we see worn out fastest.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 90, chassis code LD 90\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shimmy after a bump at speed on a solid axle vehicle\u003c\/li\u003e\n\u003cli\u003eLabour time: about 30 minutes\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eSteering damper\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 30 minutes. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809493733709,"sku":"SLS-SWV-018-S","price":64.95,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809493766477,"sku":"SLS-SWV-018-HD","price":79.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_90_Steering_Damper_b2e95baf-111d-486a-8dbf-0a6036ae4032.jpg?v=1790171316"},{"product_id":"defender-110-steering-damper","title":"Defender 110 Steering Damper","description":"\u003cp\u003eSteering Damper for the Defender 110: a steering damper to calm wheel shimmy.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 110 is the working Defender: farms, estates, utilities and expeditions, usually loaded and usually towing.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 110, chassis code LD 110\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shimmy after a bump at speed on a solid axle vehicle\u003c\/li\u003e\n\u003cli\u003eLabour time: about 30 minutes\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eSteering damper\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 30 minutes. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809494192461,"sku":"SLS-SWV-019-S","price":69.95,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809494225229,"sku":"SLS-SWV-019-HD","price":84.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_110_Steering_Damper_a8bf2ed7-de8b-4a7b-a967-8d3420e50c70.jpg?v=1790171316"},{"product_id":"defender-130-steering-damper","title":"Defender 130 Steering Damper","description":"\u003cp\u003eSteering Damper for the Defender 130: a steering damper to calm wheel shimmy.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 130 is the long wheelbase crew cab and pick up, and it carries its weight on the rear axle, which changes which parts wear first.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 130, chassis code LD 130\u003c\/li\u003e\n\u003cli\u003eEngine: 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1984 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shimmy after a bump at speed on a solid axle vehicle\u003c\/li\u003e\n\u003cli\u003eLabour time: about 30 minutes\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eSteering damper\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 30 minutes. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809494683981,"sku":"SLS-SWV-020-S","price":74.95,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809494716749,"sku":"SLS-SWV-020-HD","price":84.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_130_Steering_Damper_5918b06b-a090-4657-b776-14674a171112.jpg?v=1790171316"},{"product_id":"discovery-1-steering-damper","title":"Discovery 1 Steering Damper","description":"\u003cp\u003eSteering Damper for the Discovery 1: a steering damper to calm wheel shimmy.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shimmy after a bump at speed on a solid axle vehicle\u003c\/li\u003e\n\u003cli\u003eLabour time: about 30 minutes\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eSteering damper\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 30 minutes. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809494815053,"sku":"SLS-SWV-021-S","price":59.95,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809494847821,"sku":"SLS-SWV-021-HD","price":74.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Steering_Damper_fadbe35d-05e9-43f4-ae3e-568c74f9c47a.jpg?v=1790171316"},{"product_id":"discovery-2-steering-damper","title":"Discovery 2 Steering Damper","description":"\u003cp\u003eSteering Damper for the Discovery 2: a steering damper to calm wheel shimmy.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shimmy after a bump at speed on a solid axle vehicle\u003c\/li\u003e\n\u003cli\u003eLabour time: about 30 minutes\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 2 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eSteering damper\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 30 minutes. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809494946125,"sku":"SLS-SWV-022-S","price":64.95,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809494978893,"sku":"SLS-SWV-022-HD","price":79.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Steering_Damper_47c7f02b-fca3-4a16-bc17-f7a2ee87a8a0.jpg?v=1790171317"},{"product_id":"defender-90-track-rod-and-drag-link-set","title":"Defender 90 Track Rod and Drag Link Set","description":"\u003cp\u003eTrack Rod and Drag Link Set for the Defender 90: track rod and drag link with new joints in a heavy duty tube.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 90 is the short wheelbase and the one that gets used hardest off road, so the parts on it are the ones we see worn out fastest.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 90, chassis code LD 90\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn joints and a bent track rod\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: an alignment\u003c\/li\u003e\n\u003cli\u003eTorque: castle nuts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 11 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTrack rod\u003c\/li\u003e\n\u003cli\u003eDrag link\u003c\/li\u003e\n\u003cli\u003eJoints\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809495142733,"sku":"SLS-SWV-023-S","price":219.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809495175501,"sku":"SLS-SWV-023-HD","price":269.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_90_Track_Rod_and_Drag_Link_Set_bad82b86-2a22-468b-862b-9d9669ab2324.jpg?v=1790171317"},{"product_id":"defender-110-track-rod-and-drag-link-set","title":"Defender 110 Track Rod and Drag Link Set","description":"\u003cp\u003eTrack Rod and Drag Link Set for the Defender 110: track rod and drag link with new joints in a heavy duty tube.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 110 is the working Defender: farms, estates, utilities and expeditions, usually loaded and usually towing.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 110, chassis code LD 110\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn joints and a bent track rod\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: an alignment\u003c\/li\u003e\n\u003cli\u003eTorque: castle nuts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 11 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTrack rod\u003c\/li\u003e\n\u003cli\u003eDrag link\u003c\/li\u003e\n\u003cli\u003eJoints\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809495273805,"sku":"SLS-SWV-024-S","price":239.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809495306573,"sku":"SLS-SWV-024-HD","price":289.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_110_Track_Rod_and_Drag_Link_Set_037ea53d-9eb5-4453-b865-2ebf5d1f7d81.jpg?v=1790171360"},{"product_id":"defender-130-track-rod-and-drag-link-set","title":"Defender 130 Track Rod and Drag Link Set","description":"\u003cp\u003eTrack Rod and Drag Link Set for the Defender 130: track rod and drag link with new joints in a heavy duty tube.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The 130 is the long wheelbase crew cab and pick up, and it carries its weight on the rear axle, which changes which parts wear first.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 130, chassis code LD 130\u003c\/li\u003e\n\u003cli\u003eEngine: 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1984 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn joints and a bent track rod\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: an alignment\u003c\/li\u003e\n\u003cli\u003eTorque: castle nuts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 11 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTrack rod\u003c\/li\u003e\n\u003cli\u003eDrag link\u003c\/li\u003e\n\u003cli\u003eJoints\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809495404877,"sku":"SLS-SWV-025-S","price":249.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809495437645,"sku":"SLS-SWV-025-HD","price":299.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_130_Track_Rod_and_Drag_Link_Set_e1ee4177-7deb-4c3a-85ac-6cdfa52320e4.jpg?v=1790171360"},{"product_id":"discovery-1-track-rod-and-drag-link-set","title":"Discovery 1 Track Rod and Drag Link Set","description":"\u003cp\u003eTrack Rod and Drag Link Set for the Discovery 1: track rod and drag link with new joints in a heavy duty tube.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn joints and a bent track rod\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: an alignment\u003c\/li\u003e\n\u003cli\u003eTorque: castle nuts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 11 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTrack rod\u003c\/li\u003e\n\u003cli\u003eDrag link\u003c\/li\u003e\n\u003cli\u003eJoints\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809495896397,"sku":"SLS-SWV-026-S","price":219.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809495929165,"sku":"SLS-SWV-026-HD","price":259.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Track_Rod_and_Drag_Link_Set_c4fe1620-db72-4708-8cb5-fc576b369293.jpg?v=1790171361"},{"product_id":"discovery-2-track-rod-and-drag-link-set","title":"Discovery 2 Track Rod and Drag Link Set","description":"\u003cp\u003eTrack Rod and Drag Link Set for the Discovery 2: track rod and drag link with new joints in a heavy duty tube.\u003c\/p\u003e\u003cp\u003eThe Defender and Discovery front axle turns on swivel balls running in oil or grease, and the chrome on the ball pits and tears the seal. The symptoms are oil down the inside of the wheel and a failed MOT. Hub bearings and steering joints wear faster on a vehicle with larger tyres, and we size parts for that. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn joints and a bent track rod\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: an alignment\u003c\/li\u003e\n\u003cli\u003eTorque: castle nuts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 11 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTrack rod\u003c\/li\u003e\n\u003cli\u003eDrag link\u003c\/li\u003e\n\u003cli\u003eJoints\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809496191309,"sku":"SLS-SWV-027-S","price":219.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809496224077,"sku":"SLS-SWV-027-HD","price":269.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Track_Rod_and_Drag_Link_Set_465ef53a-fbd2-4c12-a192-141f35d8b5ec.jpg?v=1790171360"},{"product_id":"defender-90-propshaft","title":"Defender 90 Propshaft","description":"\u003cp\u003ePropshaft for the Defender 90: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 90 is the short wheelbase and the one that gets used hardest off road, so the parts on it are the ones we see worn out fastest.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 90, chassis code LD 90\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809496355149,"sku":"SLS-DRV-010-OS","price":339.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809496387917,"sku":"SLS-DRV-010-U","price":419.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809496420685,"sku":"SLS-DRV-010-GB","price":489.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_90_Propshaft_7fe5c021-bcea-4440-aba2-39f78b70dee3.jpg?v=1790171361"},{"product_id":"defender-110-propshaft","title":"Defender 110 Propshaft","description":"\u003cp\u003ePropshaft for the Defender 110: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 110 is the working Defender: farms, estates, utilities and expeditions, usually loaded and usually towing.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 110, chassis code LD 110\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809496518989,"sku":"SLS-DRV-011-OS","price":369.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809496551757,"sku":"SLS-DRV-011-U","price":449.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809496584525,"sku":"SLS-DRV-011-GB","price":519.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_110_Propshaft_4dd81b03-e367-4a92-ac10-9b5a65d4be4c.jpg?v=1790171361"},{"product_id":"defender-130-propshaft","title":"Defender 130 Propshaft","description":"\u003cp\u003ePropshaft for the Defender 130: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 130 is the long wheelbase crew cab and pick up, and it carries its weight on the rear axle, which changes which parts wear first.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 130, chassis code LD 130\u003c\/li\u003e\n\u003cli\u003eEngine: 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1984 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809496944973,"sku":"SLS-DRV-012-OS","price":389.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809496977741,"sku":"SLS-DRV-012-U","price":469.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809497010509,"sku":"SLS-DRV-012-GB","price":549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_130_Propshaft_52b5e462-2877-4f88-a5e5-608818f3ff0a.jpg?v=1790171361"},{"product_id":"discovery-1-propshaft","title":"Discovery 1 Propshaft","description":"\u003cp\u003ePropshaft for the Discovery 1: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809497108813,"sku":"SLS-DRV-013-OS","price":329.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809497141581,"sku":"SLS-DRV-013-U","price":399.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809497174349,"sku":"SLS-DRV-013-GB","price":469.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Propshaft_2628f008-8bef-46e8-b49e-7d84ef4aa1ff.jpg?v=1790171361"},{"product_id":"discovery-2-propshaft","title":"Discovery 2 Propshaft","description":"\u003cp\u003ePropshaft for the Discovery 2: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809497272653,"sku":"SLS-DRV-014-OS","price":339.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809497305421,"sku":"SLS-DRV-014-U","price":419.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809497338189,"sku":"SLS-DRV-014-GB","price":489.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Propshaft_be3b14ed-9b62-40fb-bf71-3c42c4ca3c02.jpg?v=1790171361"},{"product_id":"freelander-2-propshaft","title":"Freelander 2 Propshaft","description":"\u003cp\u003ePropshaft for the Freelander 2: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Freelander 2 is the most common vehicle through our IRD workshop by some distance, because its power transfer unit and rear coupling are both known weak points.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 2, chassis code L359\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 3.2 i6 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2006 to 2014\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809497698637,"sku":"SLS-DRV-015-OS","price":319.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809497731405,"sku":"SLS-DRV-015-U","price":399.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809497764173,"sku":"SLS-DRV-015-GB","price":459.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_2_Propshaft_f08ffeac-b237-48b1-b0ea-a0740d4dd71a.jpg?v=1790171361"},{"product_id":"range-rover-evoque-propshaft","title":"Range Rover Evoque Propshaft","description":"\u003cp\u003ePropshaft for the Range Rover Evoque: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Evoque shares its driveline with the Freelander 2, so the power transfer unit and rear coupling faults are the same ones on a smarter car.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Range Rover Evoque, chassis code L538\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 eD4 and SD4 diesel, 2.0 TD4 Ingenium, 2.0 Si4 petrol\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2011 to 2018\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809497862477,"sku":"SLS-DRV-016-OS","price":339.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809497895245,"sku":"SLS-DRV-016-U","price":409.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809497928013,"sku":"SLS-DRV-016-GB","price":479.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Range_Rover_Evoque_Propshaft_0167df1f-9505-4462-a666-e07e13f32b2c.jpg?v=1790171361"},{"product_id":"discovery-sport-propshaft","title":"Discovery Sport Propshaft","description":"\u003cp\u003ePropshaft for the Discovery Sport: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery Sport shares its driveline with the Evoque and the Freelander 2 family, including the power transfer unit and the rear coupling.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery Sport, chassis code L550\u003c\/li\u003e\n\u003cli\u003eEngine: 2.2 TD4 early, 2.0 TD4 Sd4 and Si4 Ingenium\u003c\/li\u003e\n\u003cli\u003eProduction dates: 2014 on\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809498091853,"sku":"SLS-DRV-017-OS","price":339.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809498124621,"sku":"SLS-DRV-017-U","price":419.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809498157389,"sku":"SLS-DRV-017-GB","price":489.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_Sport_Propshaft_6956fc5b-cecf-40a1-937b-a83cc2f47122.jpg?v=1790171361"},{"product_id":"freelander-1-propshaft","title":"Freelander 1 Propshaft","description":"\u003cp\u003ePropshaft for the Freelander 1: a front or rear propshaft balanced with new universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Freelander 1 runs an IRD, a viscous coupling and a rear diff in one line, and all three live or die by whether the four tyres match.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Freelander 1, chassis code L314\u003c\/li\u003e\n\u003cli\u003eEngine: 1.8 K Series, 2.0 L Series and Td4 diesel, 2.5 KV6\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1997 to 2006\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: vibration and a clunk on the drive\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1 hour\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: new bolts\u003c\/li\u003e\n\u003cli\u003eTorque: flange bolts to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 12 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePropshaft\u003c\/li\u003e\n\u003cli\u003eBolts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1 hour. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809498255693,"sku":"SLS-DRV-018-OS","price":279.0,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809498288461,"sku":"SLS-DRV-018-U","price":349.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809498321229,"sku":"SLS-DRV-018-GB","price":399.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Freelander_1_Propshaft_4d05378d-0600-4e78-a8ee-b331d1dd6390.jpg?v=1790171361"},{"product_id":"defender-90-universal-joint-pair","title":"Defender 90 Universal Joint Pair","description":"\u003cp\u003eUniversal Joint Pair for the Defender 90: a pair of greaseable universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 90 is the short wheelbase and the one that gets used hardest off road, so the parts on it are the ones we see worn out fastest.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 90, chassis code LD 90\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a clunk on take off and a vibration at speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: grease\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 1 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTwo UJs\u003c\/li\u003e\n\u003cli\u003eCirclips\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809498419533,"sku":"SLS-DRV-019-OS","price":54.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809498452301,"sku":"SLS-DRV-019-PA","price":41.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_90_Universal_Joint_Pair_d99dc0cd-dc5a-494f-b230-161f97c4762b.jpg?v=1790171362"},{"product_id":"defender-110-universal-joint-pair","title":"Defender 110 Universal Joint Pair","description":"\u003cp\u003eUniversal Joint Pair for the Defender 110: a pair of greaseable universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 110 is the working Defender: farms, estates, utilities and expeditions, usually loaded and usually towing.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 110, chassis code LD 110\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi, 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1983 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a clunk on take off and a vibration at speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: grease\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 1 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTwo UJs\u003c\/li\u003e\n\u003cli\u003eCirclips\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809498779981,"sku":"SLS-DRV-020-OS","price":59.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809498812749,"sku":"SLS-DRV-020-PA","price":43.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_110_Universal_Joint_Pair_c0ba60f7-3548-4294-93b4-3fba02e87f11.jpg?v=1790171362"},{"product_id":"defender-130-universal-joint-pair","title":"Defender 130 Universal Joint Pair","description":"\u003cp\u003eUniversal Joint Pair for the Defender 130: a pair of greaseable universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The 130 is the long wheelbase crew cab and pick up, and it carries its weight on the rear axle, which changes which parts wear first.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Defender 130, chassis code LD 130\u003c\/li\u003e\n\u003cli\u003eEngine: 300Tdi, Td5, 2.4 and 2.2 Puma diesel\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1984 to 2016\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a clunk on take off and a vibration at speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: grease\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 1 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTwo UJs\u003c\/li\u003e\n\u003cli\u003eCirclips\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809499042125,"sku":"SLS-DRV-021-OS","price":59.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809499074893,"sku":"SLS-DRV-021-PA","price":46.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Defender_130_Universal_Joint_Pair_31ad86aa-e8c8-45d8-baa3-76d6de1fe034.jpg?v=1790171362"},{"product_id":"discovery-1-universal-joint-pair","title":"Discovery 1 Universal Joint Pair","description":"\u003cp\u003eUniversal Joint Pair for the Discovery 1: a pair of greaseable universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a clunk on take off and a vibration at speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: grease\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 1 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTwo UJs\u003c\/li\u003e\n\u003cli\u003eCirclips\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809499173197,"sku":"SLS-DRV-022-OS","price":54.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809499205965,"sku":"SLS-DRV-022-PA","price":39.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Universal_Joint_Pair_3420f615-b49d-4fc6-b552-516a9160555f.jpg?v=1790171362"},{"product_id":"discovery-2-universal-joint-pair","title":"Discovery 2 Universal Joint Pair","description":"\u003cp\u003eUniversal Joint Pair for the Discovery 2: a pair of greaseable universal joints.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a clunk on take off and a vibration at speed\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: grease\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 1 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTwo UJs\u003c\/li\u003e\n\u003cli\u003eCirclips\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809499304269,"sku":"SLS-DRV-023-OS","price":54.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809499337037,"sku":"SLS-DRV-023-PA","price":41.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Universal_Joint_Pair_b9e3e46d-0607-4e07-a393-02d6bb851816.jpg?v=1790171362"}],"url":"https:\/\/solihullspares.com\/collections\/driveline.oembed?page=2","provider":"Solihull Spares","version":"1.0","type":"link"}