{"title":"Discovery 1 and 2","description":"\u003cp\u003eParts for the Discovery 1 and 2, including chassis repairs, LT230 transfer boxes, axles and Td5 engines.\u003c\/p\u003e","products":[{"product_id":"discovery-1-lt230-transfer-box-exchange","title":"Discovery 1 LT230 Transfer Box Exchange","description":"\u003cp\u003eLT230 Transfer Box Exchange for the Discovery 1: a remanufactured LT230 with new bearings, seals and centre diff, rig tested.\u003c\/p\u003e\u003cp\u003eThe transfer box splits drive between the axles and gives the low range that makes these vehicles what they are. The LT230 on the Defender, Discovery 1 and Discovery 2 is nearly unbreakable if it has oil in it and is routinely found without. The two speed units on the Discovery 3 and 4, the Sport and the Range Rover are electronically shifted and fail more often at the motor and the control module than in the gears, which is worth diagnosing before you buy a whole box. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn bearings, a leaking output seal or a noisy centre diff after years run low on oil\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a surcharge on your old box, refunded on return\u003c\/li\u003e\n\u003cli\u003eTorque: to gearbox 45 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 52 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eLT230 transfer box\u003c\/li\u003e\n\u003cli\u003eGaskets and seals\u003c\/li\u003e\n\u003cli\u003eOil fill\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809436094797,"sku":"SLS-TFB-004-R","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809436127565,"sku":"SLS-TFB-004-NU","price":1524.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_LT230_Transfer_Box_Exchange_456c8cee-08bc-437c-942b-0e036b8f53c2.jpg?v=1790170962"},{"product_id":"discovery-2-lt230-transfer-box-exchange","title":"Discovery 2 LT230 Transfer Box Exchange","description":"\u003cp\u003eLT230 Transfer Box Exchange for the Discovery 2: a remanufactured LT230 with new bearings, seals and centre diff, rig tested.\u003c\/p\u003e\u003cp\u003eThe transfer box splits drive between the axles and gives the low range that makes these vehicles what they are. The LT230 on the Defender, Discovery 1 and Discovery 2 is nearly unbreakable if it has oil in it and is routinely found without. The two speed units on the Discovery 3 and 4, the Sport and the Range Rover are electronically shifted and fail more often at the motor and the control module than in the gears, which is worth diagnosing before you buy a whole box. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn bearings, a leaking output seal or a noisy centre diff after years run low on oil\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a surcharge on your old box, refunded on return\u003c\/li\u003e\n\u003cli\u003eTorque: to gearbox 45 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 52 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eLT230 transfer box\u003c\/li\u003e\n\u003cli\u003eGaskets and seals\u003c\/li\u003e\n\u003cli\u003eOil fill\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809436291405,"sku":"SLS-TFB-005-R","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809436324173,"sku":"SLS-TFB-005-NU","price":1599.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_LT230_Transfer_Box_Exchange_753ebdf5-7424-4af1-b384-f24a5a243453.jpg?v=1790170963"},{"product_id":"discovery-1-lt230-transfer-box-rebuild-with-fitting","title":"Discovery 1 LT230 Transfer Box Rebuild with Fitting","description":"\u003cp\u003eLT230 Transfer Box Rebuild with Fitting for the Discovery 1: an LT230 removed, exchanged and refitted at our workshop with fresh oils throughout.\u003c\/p\u003e\u003cp\u003eThe transfer box splits drive between the axles and gives the low range that makes these vehicles what they are. The LT230 on the Defender, Discovery 1 and Discovery 2 is nearly unbreakable if it has oil in it and is routinely found without. The two speed units on the Discovery 3 and 4, the Sport and the Range Rover are electronically shifted and fail more often at the motor and the control module than in the gears, which is worth diagnosing before you buy a whole box. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a transfer box past its best\u003c\/li\u003e\n\u003cli\u003eLabour time: about 7 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 56 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eLT230 exchange unit\u003c\/li\u003e\n\u003cli\u003eFitting and road test\u003c\/li\u003e\n\u003cli\u003eAll oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 7 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809437241677,"sku":"SLS-TFB-009-R","price":1624.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809437274445,"sku":"SLS-TFB-009-NU","price":2174.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_LT230_Transfer_Box_Rebuild_with_Fitting_41873673-3af0-4a2a-9dbb-8c46e0cc754e.jpg?v=1790170963"},{"product_id":"discovery-2-lt230-transfer-box-rebuild-with-fitting","title":"Discovery 2 LT230 Transfer Box Rebuild with Fitting","description":"\u003cp\u003eLT230 Transfer Box Rebuild with Fitting for the Discovery 2: an LT230 removed, exchanged and refitted at our workshop with fresh oils throughout.\u003c\/p\u003e\u003cp\u003eThe transfer box splits drive between the axles and gives the low range that makes these vehicles what they are. The LT230 on the Defender, Discovery 1 and Discovery 2 is nearly unbreakable if it has oil in it and is routinely found without. The two speed units on the Discovery 3 and 4, the Sport and the Range Rover are electronically shifted and fail more often at the motor and the control module than in the gears, which is worth diagnosing before you buy a whole box. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a transfer box past its best\u003c\/li\u003e\n\u003cli\u003eLabour time: about 7 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 56 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eLT230 exchange unit\u003c\/li\u003e\n\u003cli\u003eFitting and road test\u003c\/li\u003e\n\u003cli\u003eAll oils\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 7 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809437438285,"sku":"SLS-TFB-010-R","price":1699.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809437471053,"sku":"SLS-TFB-010-NU","price":2274.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_LT230_Transfer_Box_Rebuild_with_Fitting_87f7ef3e-b759-4c43-a799-a71e96db15c9.jpg?v=1790170963"},{"product_id":"discovery-1-lt230-high-ratio-gear-set","title":"Discovery 1 LT230 High Ratio Gear Set","description":"\u003cp\u003eLT230 High Ratio Gear Set for the Discovery 1: a taller high range ratio that drops motorway revs on a vehicle on larger tyres.\u003c\/p\u003e\u003cp\u003eThe transfer box splits drive between the axles and gives the low range that makes these vehicles what they are. The LT230 on the Defender, Discovery 1 and Discovery 2 is nearly unbreakable if it has oil in it and is routinely found without. The two speed units on the Discovery 3 and 4, the Sport and the Range Rover are electronically shifted and fail more often at the motor and the control module than in the gears, which is worth diagnosing before you buy a whole box. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: engine revs and noise at cruise, particularly after a tyre size change\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a speedometer correction\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIntermediate and high output gears\u003c\/li\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. There is one specification of this, because it is the one we would fit to our own vehicles and a cheaper version would not be doing you a favour.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Default Title","offer_id":54809438093645,"sku":"SLS-TFB-014","price":569.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_LT230_High_Ratio_Gear_Set_86afda09-373a-4d2d-8ef2-b022b3c96fe1.jpg?v=1790170963"},{"product_id":"discovery-2-lt230-high-ratio-gear-set","title":"Discovery 2 LT230 High Ratio Gear Set","description":"\u003cp\u003eLT230 High Ratio Gear Set for the Discovery 2: a taller high range ratio that drops motorway revs on a vehicle on larger tyres.\u003c\/p\u003e\u003cp\u003eThe transfer box splits drive between the axles and gives the low range that makes these vehicles what they are. The LT230 on the Defender, Discovery 1 and Discovery 2 is nearly unbreakable if it has oil in it and is routinely found without. The two speed units on the Discovery 3 and 4, the Sport and the Range Rover are electronically shifted and fail more often at the motor and the control module than in the gears, which is worth diagnosing before you buy a whole box. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: engine revs and noise at cruise, particularly after a tyre size change\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a speedometer correction\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIntermediate and high output gears\u003c\/li\u003e\n\u003cli\u003eBearings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. There is one specification of this, because it is the one we would fit to our own vehicles and a cheaper version would not be doing you a favour.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Default Title","offer_id":54809438224717,"sku":"SLS-TFB-015","price":599.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_LT230_High_Ratio_Gear_Set_50f4eb93-2edb-4082-b4cf-9f63f424815f.jpg?v=1790170963"},{"product_id":"discovery-1-selectable-air-locker-kit-with-fitting","title":"Discovery 1 Selectable Air Locker Kit with Fitting","description":"\u003cp\u003eSelectable Air Locker Kit with Fitting for the Discovery 1: a selectable air operated differential locker with its compressor, switch and fitting.\u003c\/p\u003e\u003cp\u003eThe differentials on these vehicles are strong when they are fed the right oil and are not asked to do things they were never built for, like big tyres and a heavy right foot on a locked centre diff. The Discovery 3 and 4 and the Sport L320 rear electronic locking diff is a known failure; the Defender Rover diff breaks shafts before it breaks gears. Everything here says what it is rated for and what it is not. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: loss of traction with one wheel in the air\u003c\/li\u003e\n\u003cli\u003eLabour time: about 8 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a compressor mount\u003c\/li\u003e\n\u003cli\u003eTorque: crown wheel bolts 95 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 14 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eAir locker\u003c\/li\u003e\n\u003cli\u003eCompressor\u003c\/li\u003e\n\u003cli\u003eSwitch and loom\u003c\/li\u003e\n\u003cli\u003eSeals and oil\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 8 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809446842701,"sku":"SLS-DIF-007-PO","price":1349.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809446875469,"sku":"SLS-DIF-007-PAF","price":1724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Selectable_Air_Locker_Kit_with_Fitting_6289d5e6-8440-4562-b186-1be5c2474104.jpg?v=1790171014"},{"product_id":"discovery-2-selectable-air-locker-kit-with-fitting","title":"Discovery 2 Selectable Air Locker Kit with Fitting","description":"\u003cp\u003eSelectable Air Locker Kit with Fitting for the Discovery 2: a selectable air operated differential locker with its compressor, switch and fitting.\u003c\/p\u003e\u003cp\u003eThe differentials on these vehicles are strong when they are fed the right oil and are not asked to do things they were never built for, like big tyres and a heavy right foot on a locked centre diff. The Discovery 3 and 4 and the Sport L320 rear electronic locking diff is a known failure; the Defender Rover diff breaks shafts before it breaks gears. Everything here says what it is rated for and what it is not. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: loss of traction with one wheel in the air\u003c\/li\u003e\n\u003cli\u003eLabour time: about 8 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a compressor mount\u003c\/li\u003e\n\u003cli\u003eTorque: crown wheel bolts 95 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 14 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eAir locker\u003c\/li\u003e\n\u003cli\u003eCompressor\u003c\/li\u003e\n\u003cli\u003eSwitch and loom\u003c\/li\u003e\n\u003cli\u003eSeals and oil\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 8 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809446908237,"sku":"SLS-DIF-008-PO","price":1399.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809446941005,"sku":"SLS-DIF-008-PAF","price":1774.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Selectable_Air_Locker_Kit_with_Fitting_b86e4a7a-8227-4312-bd2a-ecc54398151a.jpg?v=1790171014"},{"product_id":"discovery-1-complete-front-axle-assembly","title":"Discovery 1 Complete Front Axle Assembly","description":"\u003cp\u003eComplete Front Axle Assembly for the Discovery 1: a complete remanufactured front axle with rebuilt diff, new swivels, bearings and seals.\u003c\/p\u003e\u003cp\u003eThe differentials on these vehicles are strong when they are fed the right oil and are not asked to do things they were never built for, like big tyres and a heavy right foot on a locked centre diff. The Discovery 3 and 4 and the Sport L320 rear electronic locking diff is a known failure; the Defender Rover diff breaks shafts before it breaks gears. Everything here says what it is rated for and what it is not. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: an axle with pitted swivels, a noisy diff and a leak at every seal\u003c\/li\u003e\n\u003cli\u003eLabour time: about 8 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a steering alignment\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 140 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eAxle casing\u003c\/li\u003e\n\u003cli\u003eDiff\u003c\/li\u003e\n\u003cli\u003eSwivels\u003c\/li\u003e\n\u003cli\u003eHubs\u003c\/li\u003e\n\u003cli\u003eBrakes optional\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 8 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809447203149,"sku":"SLS-DIF-012-R","price":2099.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809447235917,"sku":"SLS-DIF-012-NU","price":2824.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Complete_Front_Axle_Assembly_72acd8a0-3794-40f4-820c-bdf607b0e570.jpg?v=1790171015"},{"product_id":"discovery-2-complete-front-axle-assembly","title":"Discovery 2 Complete Front Axle Assembly","description":"\u003cp\u003eComplete Front Axle Assembly for the Discovery 2: a complete remanufactured front axle with rebuilt diff, new swivels, bearings and seals.\u003c\/p\u003e\u003cp\u003eThe differentials on these vehicles are strong when they are fed the right oil and are not asked to do things they were never built for, like big tyres and a heavy right foot on a locked centre diff. The Discovery 3 and 4 and the Sport L320 rear electronic locking diff is a known failure; the Defender Rover diff breaks shafts before it breaks gears. Everything here says what it is rated for and what it is not. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: an axle with pitted swivels, a noisy diff and a leak at every seal\u003c\/li\u003e\n\u003cli\u003eLabour time: about 8 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: a steering alignment\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 140 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eAxle casing\u003c\/li\u003e\n\u003cli\u003eDiff\u003c\/li\u003e\n\u003cli\u003eSwivels\u003c\/li\u003e\n\u003cli\u003eHubs\u003c\/li\u003e\n\u003cli\u003eBrakes optional\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 8 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809447268685,"sku":"SLS-DIF-013-R","price":2199.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809447301453,"sku":"SLS-DIF-013-NU","price":2949.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Complete_Front_Axle_Assembly_5d292f98-8205-4e56-893e-4176ab3e18af.jpg?v=1790171015"},{"product_id":"discovery-1-heavy-duty-differential","title":"Discovery 1 Heavy Duty Differential","description":"\u003cp\u003eHeavy Duty Differential for the Discovery 1: a stronger differential with uprated centre pin and cross shafts.\u003c\/p\u003e\u003cp\u003eThe differentials on these vehicles are strong when they are fed the right oil and are not asked to do things they were never built for, like big tyres and a heavy right foot on a locked centre diff. The Discovery 3 and 4 and the Sport L320 rear electronic locking diff is a known failure; the Defender Rover diff breaks shafts before it breaks gears. Everything here says what it is rated for and what it is not. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: broken centre pins and cross shafts on a Rover axle\u003c\/li\u003e\n\u003cli\u003eLabour time: about 4 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: diff oil\u003c\/li\u003e\n\u003cli\u003eTorque: crown wheel bolts 95 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 18 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDifferential\u003c\/li\u003e\n\u003cli\u003eGasket\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 4 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809447694669,"sku":"SLS-DIF-019-S","price":669.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809447727437,"sku":"SLS-DIF-019-HD","price":799.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Heavy_Duty_Differential_f2f096cd-f8eb-4e69-80af-ae25de0d08fe.jpg?v=1790171061"},{"product_id":"discovery-2-heavy-duty-differential","title":"Discovery 2 Heavy Duty Differential","description":"\u003cp\u003eHeavy Duty Differential for the Discovery 2: a stronger differential with uprated centre pin and cross shafts.\u003c\/p\u003e\u003cp\u003eThe differentials on these vehicles are strong when they are fed the right oil and are not asked to do things they were never built for, like big tyres and a heavy right foot on a locked centre diff. The Discovery 3 and 4 and the Sport L320 rear electronic locking diff is a known failure; the Defender Rover diff breaks shafts before it breaks gears. Everything here says what it is rated for and what it is not. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: broken centre pins and cross shafts on a Rover axle\u003c\/li\u003e\n\u003cli\u003eLabour time: about 4 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: diff oil\u003c\/li\u003e\n\u003cli\u003eTorque: crown wheel bolts 95 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 18 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDifferential\u003c\/li\u003e\n\u003cli\u003eGasket\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 4 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809447760205,"sku":"SLS-DIF-020-S","price":699.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809447792973,"sku":"SLS-DIF-020-HD","price":829.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Heavy_Duty_Differential_98f06e74-09de-4563-aaa5-7d8cb08f3c5f.jpg?v=1790171061"},{"product_id":"discovery-1-heavy-duty-half-shaft-pair","title":"Discovery 1 Heavy Duty Half Shaft Pair","description":"\u003cp\u003eHeavy Duty Half Shaft Pair for the Discovery 1: a pair of heavy duty half shafts in a stronger alloy.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shafts twisted or snapped at the spline off road\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub oil seals\u003c\/li\u003e\n\u003cli\u003eTorque: drive flange 65 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 16 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eTwo half shafts\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809448055117,"sku":"SLS-DRV-008-S","price":379.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809448087885,"sku":"SLS-DRV-008-HD","price":459.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Heavy_Duty_Half_Shaft_Pair_603136df-d495-4f8d-a313-b230f23821a0.jpg?v=1790171062"},{"product_id":"discovery-2-heavy-duty-half-shaft-pair","title":"Discovery 2 Heavy Duty Half Shaft Pair","description":"\u003cp\u003eHeavy Duty Half Shaft Pair for the Discovery 2: a pair of heavy duty half shafts in a stronger alloy.\u003c\/p\u003e\u003cp\u003ePropshafts, universal joints, drive flanges and half shafts take every bit of torque the engine makes, and they fail with a clunk, a vibration or a sudden loss of drive. Most of it is cheap to replace before it fails and expensive after. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: shafts twisted or snapped at the spline off road\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: hub oil seals\u003c\/li\u003e\n\u003cli\u003eTorque: drive flange 65 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 16 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eTwo half shafts\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809448186189,"sku":"SLS-DRV-009-S","price":399.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809448218957,"sku":"SLS-DRV-009-HD","price":469.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Heavy_Duty_Half_Shaft_Pair_3f4db813-68f9-4b06-83f3-511ad7c20bd0.jpg?v=1790171062"},{"product_id":"discovery-1-300tdi-reconditioned-engine","title":"Discovery 1 300Tdi Reconditioned Engine","description":"\u003cp\u003e300Tdi Reconditioned Engine for the Discovery 1: a fully reconditioned 300Tdi with a new timing belt kit and injectors tested.\u003c\/p\u003e\u003cp\u003eThe 2.7 and 3.0 V6 diesels in the Discovery 3 and 4, the Sport and the later L322 can spin a bearing and break the crankshaft, which is an engine out job and the single largest bill these vehicles produce. The early signs are low oil pressure warnings, a knock at idle and metal in the oil. These packages rebuild the engine properly with the revised parts, rather than dropping in a used engine with the same history. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured or New Unit\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a worn 300Tdi with blow by, low compression or a failed head\u003c\/li\u003e\n\u003cli\u003eLabour time: about 14 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: fresh coolant and oil\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 230 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEngine\u003c\/li\u003e\n\u003cli\u003eTiming belt kit\u003c\/li\u003e\n\u003cli\u003eGaskets\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 14 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. We do not sell particulate filter deletes, EGR blanking plates, AdBlue emulators or emissions defeat software. They are illegal on a road vehicle in the UK, an MOT failure and they void insurance.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. New Unit is a brand new unit rather than an exchange, for when your old one is past rebuilding or you cannot be without the vehicle while we assess the core.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Remanufactured","offer_id":54809448939853,"sku":"SLS-ENG-017-R","price":2774.0,"currency_code":"GBP","in_stock":true},{"title":"New Unit","offer_id":54809448972621,"sku":"SLS-ENG-017-NU","price":3724.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_300Tdi_Reconditioned_Engine_b3f2278c-845b-4008-af3d-33015043ce2e.jpg?v=1790171064"},{"product_id":"discovery-2-td5-reconditioned-engine","title":"Discovery 2 Td5 Reconditioned Engine","description":"\u003cp\u003eTd5 Reconditioned Engine for the Discovery 2: a reconditioned Td5 with new injector loom, seals and a pressure tested head.\u003c\/p\u003e\u003cp\u003eThe 2.7 and 3.0 V6 diesels in the Discovery 3 and 4, the Sport and the later L322 can spin a bearing and break the crankshaft, which is an engine out job and the single largest bill these vehicles produce. The early signs are low oil pressure warnings, a knock at idle and metal in the oil. These packages rebuild the engine properly with the revised parts, rather than dropping in a used engine with the same history. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Remanufactured\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a tired Td5 with a cracked head or worn bores\u003c\/li\u003e\n\u003cli\u003eLabour time: about 14 hours\u003c\/li\u003e\n\u003cli\u003eCoding: programming with a proper diagnostic system is required after fitting, and we can do it at the workshop or supply the procedure for your garage\u003c\/li\u003e\n\u003cli\u003eAlso needed: fresh coolant and oil\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 240 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEngine\u003c\/li\u003e\n\u003cli\u003eInjector loom\u003c\/li\u003e\n\u003cli\u003eGaskets\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 14 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. We do not sell particulate filter deletes, EGR blanking plates, AdBlue emulators or emissions defeat software. They are illegal on a road vehicle in the UK, an MOT failure and they void insurance.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eRemanufactured is stripped to the casting, measured, rebuilt with new bearings seals and wear parts and rig tested, with a surcharge refunded on your old unit. There is one specification of this, because it is the one we would fit to our own vehicles and a cheaper version would not be doing you a favour.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Default Title","offer_id":54809449103693,"sku":"SLS-ENG-021","price":3199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Td5_Reconditioned_Engine_197922f8-ce7c-44c8-b197-5f050941bd43.jpg?v=1790171064"},{"product_id":"discovery-1-galvanised-chassis","title":"Discovery 1 Galvanised Chassis","description":"\u003cp\u003eGalvanised Chassis for the Discovery 1: a complete replacement chassis, jig built and hot dip galvanised.\u003c\/p\u003e\u003cp\u003eA Defender or Discovery 1 is only as good as its chassis, and the original was painted steel that rusts from the inside out: rear crossmember first, then the outriggers, then the main rails behind the rear wheels. A galvanised replacement chassis is the permanent answer and adds decades to the vehicle. The bulkhead rusts in the footwells and along the top rail, and on a Defender it is the other half of the same decision. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Galvanised or Painted\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: rust through of the rear crossmember, outriggers and main rails\u003c\/li\u003e\n\u003cli\u003eLabour time: a body off job of several days\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: new mounts and fixings, which we can supply as a kit\u003c\/li\u003e\n\u003cli\u003eTorque: body mounts 25 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 220 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: lifetime against rust through on the galvanising, two years on the parts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eChassis frame\u003c\/li\u003e\n\u003cli\u003eMount points for all standard fittings\u003c\/li\u003e\n\u003cli\u003eChassis number plate location\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: a body off job of several days. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eGalvanised is hot dip galvanised after fabrication, inside and out, which is what stops the rust that finished the original. Painted is supplied in black primer and top coat for a correct appearance, with cavity wax recommended after fitting.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Galvanised","offer_id":54809450250573,"sku":"SLS-CHS-004-G","price":3349.0,"currency_code":"GBP","in_stock":true},{"title":"Painted","offer_id":54809450283341,"sku":"SLS-CHS-004-P","price":2824.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Galvanised_Chassis_79eb5403-7034-4c8d-a0a9-3be7a532800f.jpg?v=1790171066"},{"product_id":"discovery-1-rear-chassis-section-repair-package","title":"Discovery 1 Rear Chassis Section Repair Package","description":"\u003cp\u003eRear Chassis Section Repair Package for the Discovery 1: a galvanised rear quarter chassis section and crossmember, welded in at our workshop.\u003c\/p\u003e\u003cp\u003eA Defender or Discovery 1 is only as good as its chassis, and the original was painted steel that rusts from the inside out: rear crossmember first, then the outriggers, then the main rails behind the rear wheels. A galvanised replacement chassis is the permanent answer and adds decades to the vehicle. The bulkhead rusts in the footwells and along the top rail, and on a Defender it is the other half of the same decision. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Galvanised or Painted\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: rotten rear chassis legs and crossmember on an otherwise sound chassis\u003c\/li\u003e\n\u003cli\u003eLabour time: about 16 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: cavity wax\u003c\/li\u003e\n\u003cli\u003eTorque: welded\u003c\/li\u003e\n\u003cli\u003eWeight: about 70 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: lifetime against rust through on the galvanising, two years on the parts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRear chassis section\u003c\/li\u003e\n\u003cli\u003eCrossmember\u003c\/li\u003e\n\u003cli\u003eWelding\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 16 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eGalvanised is hot dip galvanised after fabrication, inside and out, which is what stops the rust that finished the original. Painted is supplied in black primer and top coat for a correct appearance, with cavity wax recommended after fitting.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Galvanised","offer_id":54809450873165,"sku":"SLS-CHS-013-G","price":1249.0,"currency_code":"GBP","in_stock":true},{"title":"Painted","offer_id":54809450905933,"sku":"SLS-CHS-013-P","price":1049.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Rear_Chassis_Section_Repair_Package_d5d33e35-a1f4-4729-958a-d30c87cec8aa.jpg?v=1790171112"},{"product_id":"discovery-2-rear-chassis-section-repair-package","title":"Discovery 2 Rear Chassis Section Repair Package","description":"\u003cp\u003eRear Chassis Section Repair Package for the Discovery 2: a galvanised rear quarter chassis section and crossmember, welded in at our workshop.\u003c\/p\u003e\u003cp\u003eA Defender or Discovery 1 is only as good as its chassis, and the original was painted steel that rusts from the inside out: rear crossmember first, then the outriggers, then the main rails behind the rear wheels. A galvanised replacement chassis is the permanent answer and adds decades to the vehicle. The bulkhead rusts in the footwells and along the top rail, and on a Defender it is the other half of the same decision. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Galvanised or Painted\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: rotten rear chassis legs and crossmember on an otherwise sound chassis\u003c\/li\u003e\n\u003cli\u003eLabour time: about 16 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: cavity wax\u003c\/li\u003e\n\u003cli\u003eTorque: welded\u003c\/li\u003e\n\u003cli\u003eWeight: about 70 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: lifetime against rust through on the galvanising, two years on the parts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRear chassis section\u003c\/li\u003e\n\u003cli\u003eCrossmember\u003c\/li\u003e\n\u003cli\u003eWelding\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 16 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eGalvanised is hot dip galvanised after fabrication, inside and out, which is what stops the rust that finished the original. Painted is supplied in black primer and top coat for a correct appearance, with cavity wax recommended after fitting.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Galvanised","offer_id":54809450938701,"sku":"SLS-CHS-014-G","price":1299.0,"currency_code":"GBP","in_stock":true},{"title":"Painted","offer_id":54809450971469,"sku":"SLS-CHS-014-P","price":1099.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Rear_Chassis_Section_Repair_Package_cbe4a25f-3d7c-4d44-a0d0-e33e446dc241.jpg?v=1790171112"},{"product_id":"discovery-1-galvanised-rear-crossmember","title":"Discovery 1 Galvanised Rear Crossmember","description":"\u003cp\u003eGalvanised Rear Crossmember for the Discovery 1: a galvanised rear crossmember with the towing mount points.\u003c\/p\u003e\u003cp\u003ePanels for vehicles that get used: Defender door frames, wings, bulkhead sections and floor panels, and the aluminium and steel panels for the later vehicles. Defender panels are mostly aluminium on steel frames, and the steel frame is almost always the part that has rotted. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Galvanised or Painted\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the crossmember is usually the first part of the chassis to go\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours welded\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: cavity wax\u003c\/li\u003e\n\u003cli\u003eTorque: welded\u003c\/li\u003e\n\u003cli\u003eWeight: about 22 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: lifetime against rust through on the galvanising, two years on the parts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eCrossmember\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours welded. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eGalvanised is hot dip galvanised after fabrication, inside and out, which is what stops the rust that finished the original. Painted is supplied in black primer and top coat for a correct appearance, with cavity wax recommended after fitting.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Galvanised","offer_id":54809451233613,"sku":"SLS-BOD-004-G","price":249.0,"currency_code":"GBP","in_stock":true},{"title":"Painted","offer_id":54809451266381,"sku":"SLS-BOD-004-P","price":209.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Galvanised_Rear_Crossmember_b905fcfe-4e9b-4176-8617-b7e0d44b81d0.jpg?v=1790171113"},{"product_id":"discovery-2-galvanised-rear-crossmember","title":"Discovery 2 Galvanised Rear Crossmember","description":"\u003cp\u003eGalvanised Rear Crossmember for the Discovery 2: a galvanised rear crossmember with the towing mount points.\u003c\/p\u003e\u003cp\u003ePanels for vehicles that get used: Defender door frames, wings, bulkhead sections and floor panels, and the aluminium and steel panels for the later vehicles. Defender panels are mostly aluminium on steel frames, and the steel frame is almost always the part that has rotted. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Galvanised or Painted\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: the crossmember is usually the first part of the chassis to go\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours welded\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: cavity wax\u003c\/li\u003e\n\u003cli\u003eTorque: welded\u003c\/li\u003e\n\u003cli\u003eWeight: about 22 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: lifetime against rust through on the galvanising, two years on the parts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eCrossmember\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours welded. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eGalvanised is hot dip galvanised after fabrication, inside and out, which is what stops the rust that finished the original. Painted is supplied in black primer and top coat for a correct appearance, with cavity wax recommended after fitting.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Galvanised","offer_id":54809451299149,"sku":"SLS-BOD-005-G","price":259.0,"currency_code":"GBP","in_stock":true},{"title":"Painted","offer_id":54809451331917,"sku":"SLS-BOD-005-P","price":219.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Galvanised_Rear_Crossmember_7942f0b0-d13a-4036-be68-a4c00fb52706.jpg?v=1790171112"},{"product_id":"discovery-1-galvanised-outrigger-pair","title":"Discovery 1 Galvanised Outrigger Pair","description":"\u003cp\u003eGalvanised Outrigger Pair for the Discovery 1: a pair of galvanised chassis outriggers.\u003c\/p\u003e\u003cp\u003ePanels for vehicles that get used: Defender door frames, wings, bulkhead sections and floor panels, and the aluminium and steel panels for the later vehicles. Defender panels are mostly aluminium on steel frames, and the steel frame is almost always the part that has rotted. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Galvanised or Painted\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: outriggers rot at the body mounts and fail the MOT\u003c\/li\u003e\n\u003cli\u003eLabour time: about 4 hours welded\u003c\/li\u003e\n\u003cli\u003eCoding: none. This vehicle predates the modules that need it\u003c\/li\u003e\n\u003cli\u003eAlso needed: body mount rubbers\u003c\/li\u003e\n\u003cli\u003eTorque: welded\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: lifetime against rust through on the galvanising, two years on the parts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eTwo outriggers\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 4 hours welded. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eGalvanised is hot dip galvanised after fabrication, inside and out, which is what stops the rust that finished the original. Painted is supplied in black primer and top coat for a correct appearance, with cavity wax recommended after fitting.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Galvanised","offer_id":54809451561293,"sku":"SLS-BOD-009-G","price":159.95,"currency_code":"GBP","in_stock":true},{"title":"Painted","offer_id":54809451594061,"sku":"SLS-BOD-009-P","price":134.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Galvanised_Outrigger_Pair_4f597082-af7c-438e-839e-b29056a02132.jpg?v=1790171113"},{"product_id":"discovery-1-winch-bumper-package","title":"Discovery 1 Winch Bumper Package","description":"\u003cp\u003eWinch Bumper Package for the Discovery 1: a winch rated at one and a half times gross vehicle weight on a tested bumper, with synthetic rope, fairlead, wiring and isolator.\u003c\/p\u003e\u003cp\u003eA winch is rated for straight line pulling, and the rule we work to is a winch rated at one and a half times the gross vehicle weight, because mud, gradient and a bogged vehicle all multiply the load. Every package here is sized to the vehicle rather than to the box, with a bumper tested to carry the winch, the correct cable or synthetic rope, and the wiring and isolator to run it safely. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a vehicle that goes off road without a means of self recovery\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours\u003c\/li\u003e\n\u003cli\u003eCoding: programming with a proper diagnostic system is required after fitting, and we can do it at the workshop or supply the procedure for your garage\u003c\/li\u003e\n\u003cli\u003eAlso needed: a split charge or heavy duty battery\u003c\/li\u003e\n\u003cli\u003eTorque: bumper to chassis 110 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 62 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWinch\u003c\/li\u003e\n\u003cli\u003eWinch bumper\u003c\/li\u003e\n\u003cli\u003eSynthetic rope\u003c\/li\u003e\n\u003cli\u003eHawse fairlead\u003c\/li\u003e\n\u003cli\u003eWiring and isolator\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809452085581,"sku":"SLS-WIN-005-PO","price":2199.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809452118349,"sku":"SLS-WIN-005-PAF","price":2824.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Winch_Bumper_Package_c07c0b8a-49d0-499f-bef4-a9e9edb58ffe.jpg?v=1790171114"},{"product_id":"discovery-2-winch-bumper-package","title":"Discovery 2 Winch Bumper Package","description":"\u003cp\u003eWinch Bumper Package for the Discovery 2: a winch rated at one and a half times gross vehicle weight on a tested bumper, with synthetic rope, fairlead, wiring and isolator.\u003c\/p\u003e\u003cp\u003eA winch is rated for straight line pulling, and the rule we work to is a winch rated at one and a half times the gross vehicle weight, because mud, gradient and a bogged vehicle all multiply the load. Every package here is sized to the vehicle rather than to the box, with a bumper tested to carry the winch, the correct cable or synthetic rope, and the wiring and isolator to run it safely. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a vehicle that goes off road without a means of self recovery\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours\u003c\/li\u003e\n\u003cli\u003eCoding: programming with a proper diagnostic system is required after fitting, and we can do it at the workshop or supply the procedure for your garage\u003c\/li\u003e\n\u003cli\u003eAlso needed: a split charge or heavy duty battery\u003c\/li\u003e\n\u003cli\u003eTorque: bumper to chassis 110 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 62 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWinch\u003c\/li\u003e\n\u003cli\u003eWinch bumper\u003c\/li\u003e\n\u003cli\u003eSynthetic rope\u003c\/li\u003e\n\u003cli\u003eHawse fairlead\u003c\/li\u003e\n\u003cli\u003eWiring and isolator\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809452183885,"sku":"SLS-WIN-006-PO","price":2299.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809452216653,"sku":"SLS-WIN-006-PAF","price":2949.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Winch_Bumper_Package_90d75a28-44a0-4396-a490-466438cad76b.jpg?v=1790171114"},{"product_id":"discovery-1-winch-bumper-and-recovery-kit-package","title":"Discovery 1 Winch Bumper and Recovery Kit Package","description":"\u003cp\u003eWinch Bumper and Recovery Kit Package for the Discovery 1: the winch bumper package plus a full recovery kit and rated recovery points front and rear.\u003c\/p\u003e\u003cp\u003eA winch is rated for straight line pulling, and the rule we work to is a winch rated at one and a half times the gross vehicle weight, because mud, gradient and a bogged vehicle all multiply the load. Every package here is sized to the vehicle rather than to the box, with a bumper tested to carry the winch, the correct cable or synthetic rope, and the wiring and isolator to run it safely. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: being stuck with nothing rated to pull from\u003c\/li\u003e\n\u003cli\u003eLabour time: about 7 hours\u003c\/li\u003e\n\u003cli\u003eCoding: programming with a proper diagnostic system is required after fitting, and we can do it at the workshop or supply the procedure for your garage\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: bumper 110 Nm, recovery points to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 78 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWinch\u003c\/li\u003e\n\u003cli\u003eBumper\u003c\/li\u003e\n\u003cli\u003eRope\u003c\/li\u003e\n\u003cli\u003eRecovery points\u003c\/li\u003e\n\u003cli\u003eSnatch block\u003c\/li\u003e\n\u003cli\u003eShackles\u003c\/li\u003e\n\u003cli\u003eTree strop\u003c\/li\u003e\n\u003cli\u003eKinetic rope\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 7 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809452642637,"sku":"SLS-WIN-014-PO","price":2674.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809452675405,"sku":"SLS-WIN-014-PAF","price":3424.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Winch_Bumper_and_Recovery_Kit_Package_02d1518f-06dc-4bc8-9a5c-b99f22e07cdd.jpg?v=1790171115"},{"product_id":"discovery-2-winch-bumper-and-recovery-kit-package","title":"Discovery 2 Winch Bumper and Recovery Kit Package","description":"\u003cp\u003eWinch Bumper and Recovery Kit Package for the Discovery 2: the winch bumper package plus a full recovery kit and rated recovery points front and rear.\u003c\/p\u003e\u003cp\u003eA winch is rated for straight line pulling, and the rule we work to is a winch rated at one and a half times the gross vehicle weight, because mud, gradient and a bogged vehicle all multiply the load. Every package here is sized to the vehicle rather than to the box, with a bumper tested to carry the winch, the correct cable or synthetic rope, and the wiring and isolator to run it safely. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: being stuck with nothing rated to pull from\u003c\/li\u003e\n\u003cli\u003eLabour time: about 7 hours\u003c\/li\u003e\n\u003cli\u003eCoding: programming with a proper diagnostic system is required after fitting, and we can do it at the workshop or supply the procedure for your garage\u003c\/li\u003e\n\u003cli\u003eAlso needed: nothing\u003c\/li\u003e\n\u003cli\u003eTorque: bumper 110 Nm, recovery points to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 78 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWinch\u003c\/li\u003e\n\u003cli\u003eBumper\u003c\/li\u003e\n\u003cli\u003eRope\u003c\/li\u003e\n\u003cli\u003eRecovery points\u003c\/li\u003e\n\u003cli\u003eSnatch block\u003c\/li\u003e\n\u003cli\u003eShackles\u003c\/li\u003e\n\u003cli\u003eTree strop\u003c\/li\u003e\n\u003cli\u003eKinetic rope\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 7 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809452708173,"sku":"SLS-WIN-015-PO","price":2799.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809452740941,"sku":"SLS-WIN-015-PAF","price":3574.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Winch_Bumper_and_Recovery_Kit_Package_a2207ddc-1f1a-4dee-9b64-d60b0bb20e80.jpg?v=1790171115"},{"product_id":"discovery-1-heavy-duty-winch","title":"Discovery 1 Heavy Duty Winch","description":"\u003cp\u003eHeavy Duty Winch for the Discovery 1: a heavy duty electric winch with synthetic rope and a wireless controller.\u003c\/p\u003e\u003cp\u003eA winch is rated for straight line pulling, and the rule we work to is a winch rated at one and a half times the gross vehicle weight, because mud, gradient and a bogged vehicle all multiply the load. Every package here is sized to the vehicle rather than to the box, with a bumper tested to carry the winch, the correct cable or synthetic rope, and the wiring and isolator to run it safely. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: self recovery\u003c\/li\u003e\n\u003cli\u003eLabour time: about 3 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a winch mount or bumper\u003c\/li\u003e\n\u003cli\u003eTorque: mounting 45 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 32 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWinch\u003c\/li\u003e\n\u003cli\u003eSynthetic rope\u003c\/li\u003e\n\u003cli\u003eFairlead\u003c\/li\u003e\n\u003cli\u003eController\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 3 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809453166925,"sku":"SLS-WIN-023-S","price":1049.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809453199693,"sku":"SLS-WIN-023-HD","price":1249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Heavy_Duty_Winch_54b2b133-77e7-49a8-9201-0a6a23bec153.jpg?v=1790171116"},{"product_id":"discovery-2-heavy-duty-winch","title":"Discovery 2 Heavy Duty Winch","description":"\u003cp\u003eHeavy Duty Winch for the Discovery 2: a heavy duty electric winch with synthetic rope and a wireless controller.\u003c\/p\u003e\u003cp\u003eA winch is rated for straight line pulling, and the rule we work to is a winch rated at one and a half times the gross vehicle weight, because mud, gradient and a bogged vehicle all multiply the load. Every package here is sized to the vehicle rather than to the box, with a bumper tested to carry the winch, the correct cable or synthetic rope, and the wiring and isolator to run it safely. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: self recovery\u003c\/li\u003e\n\u003cli\u003eLabour time: about 3 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a winch mount or bumper\u003c\/li\u003e\n\u003cli\u003eTorque: mounting 45 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 32 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWinch\u003c\/li\u003e\n\u003cli\u003eSynthetic rope\u003c\/li\u003e\n\u003cli\u003eFairlead\u003c\/li\u003e\n\u003cli\u003eController\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 3 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809453232461,"sku":"SLS-WIN-024-S","price":1099.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809453265229,"sku":"SLS-WIN-024-HD","price":1324.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Heavy_Duty_Winch_92ba149c-039c-4cc5-9512-641098be0429.jpg?v=1790171116"},{"product_id":"discovery-1-rear-recovery-bumper-with-towing-point","title":"Discovery 1 Rear Recovery Bumper with Towing Point","description":"\u003cp\u003eRear Recovery Bumper with Towing Point for the Discovery 1: a steel rear bumper with rated recovery points and a tow mount.\u003c\/p\u003e\u003cp\u003eProtection and practical equipment for vehicles that leave the tarmac: snorkels, underbody guards, rock sliders, roof racks, ladders and lighting. Chosen for strength rather than appearance, and each one lists its weight and whether it affects insurance or MOT. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Galvanised or Painted\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rear crossmember with nowhere rated to recover from\u003c\/li\u003e\n\u003cli\u003eLabour time: about 3 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: tow electrics if not fitted\u003c\/li\u003e\n\u003cli\u003eTorque: 110 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 38 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRear bumper\u003c\/li\u003e\n\u003cli\u003eRecovery points\u003c\/li\u003e\n\u003cli\u003eFixings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 3 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eGalvanised is hot dip galvanised after fabrication, inside and out, which is what stops the rust that finished the original. Painted is supplied in black primer and top coat for a correct appearance, with cavity wax recommended after fitting.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Galvanised","offer_id":54809454575949,"sku":"SLS-OFF-005-G","price":719.0,"currency_code":"GBP","in_stock":true},{"title":"Painted","offer_id":54809454608717,"sku":"SLS-OFF-005-P","price":599.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Rear_Recovery_Bumper_with_Towing_Point_234e1eee-46f3-4b05-abd3-0ddba4688be8.jpg?v=1790171161"},{"product_id":"discovery-2-rear-recovery-bumper-with-towing-point","title":"Discovery 2 Rear Recovery Bumper with Towing Point","description":"\u003cp\u003eRear Recovery Bumper with Towing Point for the Discovery 2: a steel rear bumper with rated recovery points and a tow mount.\u003c\/p\u003e\u003cp\u003eProtection and practical equipment for vehicles that leave the tarmac: snorkels, underbody guards, rock sliders, roof racks, ladders and lighting. Chosen for strength rather than appearance, and each one lists its weight and whether it affects insurance or MOT. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Galvanised or Painted\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a rear crossmember with nowhere rated to recover from\u003c\/li\u003e\n\u003cli\u003eLabour time: about 3 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: tow electrics if not fitted\u003c\/li\u003e\n\u003cli\u003eTorque: 110 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 38 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRear bumper\u003c\/li\u003e\n\u003cli\u003eRecovery points\u003c\/li\u003e\n\u003cli\u003eFixings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 3 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eGalvanised is hot dip galvanised after fabrication, inside and out, which is what stops the rust that finished the original. Painted is supplied in black primer and top coat for a correct appearance, with cavity wax recommended after fitting.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Galvanised","offer_id":54809454641485,"sku":"SLS-OFF-006-G","price":739.0,"currency_code":"GBP","in_stock":true},{"title":"Painted","offer_id":54809454674253,"sku":"SLS-OFF-006-P","price":629.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Rear_Recovery_Bumper_with_Towing_Point_03f2790f-aa15-4519-8f5c-8b4c7cfa71b1.jpg?v=1790171161"},{"product_id":"discovery-1-overland-expedition-package","title":"Discovery 1 Overland Expedition Package","description":"\u003cp\u003eOverland Expedition Package for the Discovery 1: roof rack, roof tent, awning, dual battery system, fridge mount and underbody protection.\u003c\/p\u003e\u003cp\u003eThese are the packages we would build for our own vehicles before a long trip: the parts that fail far from home, the protection that stops a rock ending the journey, and the equipment that makes living out of the vehicle possible. Each one lists its weight, because an expedition vehicle is usually overweight before it has left the country and payload is the thing people forget to check. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a vehicle that can drive a long way but cannot live there\u003c\/li\u003e\n\u003cli\u003eLabour time: about 14 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a payload check, which we do\u003c\/li\u003e\n\u003cli\u003eTorque: to each manufacturer\u003c\/li\u003e\n\u003cli\u003eWeight: about 210 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRoof rack\u003c\/li\u003e\n\u003cli\u003eRoof tent\u003c\/li\u003e\n\u003cli\u003eAwning\u003c\/li\u003e\n\u003cli\u003eDual battery\u003c\/li\u003e\n\u003cli\u003eFridge slide\u003c\/li\u003e\n\u003cli\u003eSump and tank guards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 14 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. There is one specification of this, because it is the one we would fit to our own vehicles and a cheaper version would not be doing you a favour.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Default Title","offer_id":54809456410957,"sku":"SLS-OVL-005","price":3449.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Overland_Expedition_Package_09112138-3062-43a2-99b3-992ba1a19cc7.jpg?v=1790171163"},{"product_id":"discovery-2-overland-expedition-package","title":"Discovery 2 Overland Expedition Package","description":"\u003cp\u003eOverland Expedition Package for the Discovery 2: roof rack, roof tent, awning, dual battery system, fridge mount and underbody protection.\u003c\/p\u003e\u003cp\u003eThese are the packages we would build for our own vehicles before a long trip: the parts that fail far from home, the protection that stops a rock ending the journey, and the equipment that makes living out of the vehicle possible. Each one lists its weight, because an expedition vehicle is usually overweight before it has left the country and payload is the thing people forget to check. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a vehicle that can drive a long way but cannot live there\u003c\/li\u003e\n\u003cli\u003eLabour time: about 14 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a payload check, which we do\u003c\/li\u003e\n\u003cli\u003eTorque: to each manufacturer\u003c\/li\u003e\n\u003cli\u003eWeight: about 210 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRoof rack\u003c\/li\u003e\n\u003cli\u003eRoof tent\u003c\/li\u003e\n\u003cli\u003eAwning\u003c\/li\u003e\n\u003cli\u003eDual battery\u003c\/li\u003e\n\u003cli\u003eFridge slide\u003c\/li\u003e\n\u003cli\u003eSump and tank guards\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 14 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. There is one specification of this, because it is the one we would fit to our own vehicles and a cheaper version would not be doing you a favour.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Default Title","offer_id":54809456804173,"sku":"SLS-OVL-006","price":3599.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Overland_Expedition_Package_8c8de77c-54b8-490f-aa93-f9f69325d039.jpg?v=1790171163"},{"product_id":"discovery-1-expedition-spares-and-protection-package","title":"Discovery 1 Expedition Spares and Protection Package","description":"\u003cp\u003eExpedition Spares and Protection Package for the Discovery 1: the spares that fail far from home plus steering and sump guards.\u003c\/p\u003e\u003cp\u003eThese are the packages we would build for our own vehicles before a long trip: the parts that fail far from home, the protection that stops a rock ending the journey, and the equipment that makes living out of the vehicle possible. Each one lists its weight, because an expedition vehicle is usually overweight before it has left the country and payload is the thing people forget to check. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a breakdown a long way from a parts counter\u003c\/li\u003e\n\u003cli\u003eLabour time: guards about 3 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a roadside tool kit\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 42 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFan belt and hoses\u003c\/li\u003e\n\u003cli\u003eFilters\u003c\/li\u003e\n\u003cli\u003eUJs\u003c\/li\u003e\n\u003cli\u003eWheel bearings\u003c\/li\u003e\n\u003cli\u003eSteering guard\u003c\/li\u003e\n\u003cli\u003eSump guard\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: guards about 3 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. There is one specification of this, because it is the one we would fit to our own vehicles and a cheaper version would not be doing you a favour.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Default Title","offer_id":54809457328461,"sku":"SLS-OVL-014","price":1424.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Expedition_Spares_and_Protection_Package_95fa2696-71a3-455c-a082-1f0ba7440852.jpg?v=1790171164"},{"product_id":"discovery-2-expedition-spares-and-protection-package","title":"Discovery 2 Expedition Spares and Protection Package","description":"\u003cp\u003eExpedition Spares and Protection Package for the Discovery 2: the spares that fail far from home plus steering and sump guards.\u003c\/p\u003e\u003cp\u003eThese are the packages we would build for our own vehicles before a long trip: the parts that fail far from home, the protection that stops a rock ending the journey, and the equipment that makes living out of the vehicle possible. Each one lists its weight, because an expedition vehicle is usually overweight before it has left the country and payload is the thing people forget to check. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a breakdown a long way from a parts counter\u003c\/li\u003e\n\u003cli\u003eLabour time: guards about 3 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a roadside tool kit\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 42 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFan belt and hoses\u003c\/li\u003e\n\u003cli\u003eFilters\u003c\/li\u003e\n\u003cli\u003eUJs\u003c\/li\u003e\n\u003cli\u003eWheel bearings\u003c\/li\u003e\n\u003cli\u003eSteering guard\u003c\/li\u003e\n\u003cli\u003eSump guard\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: guards about 3 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. There is one specification of this, because it is the one we would fit to our own vehicles and a cheaper version would not be doing you a favour.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Default Title","offer_id":54809457361229,"sku":"SLS-OVL-015","price":1499.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Expedition_Spares_and_Protection_Package_e88c3e97-ece8-4e85-8b8a-8c45ceb5967f.jpg?v=1790171164"},{"product_id":"discovery-1-dual-battery-and-power-package","title":"Discovery 1 Dual Battery and Power Package","description":"\u003cp\u003eDual Battery and Power Package for the Discovery 1: a DC to DC charger, a lithium leisure battery, isolator and wiring.\u003c\/p\u003e\u003cp\u003eThese are the packages we would build for our own vehicles before a long trip: the parts that fail far from home, the protection that stops a rock ending the journey, and the equipment that makes living out of the vehicle possible. Each one lists its weight, because an expedition vehicle is usually overweight before it has left the country and payload is the thing people forget to check. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a flat starter battery after a night running a fridge\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a battery tray\u003c\/li\u003e\n\u003cli\u003eTorque: terminals 8 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 18 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDC to DC charger\u003c\/li\u003e\n\u003cli\u003eLithium battery\u003c\/li\u003e\n\u003cli\u003eIsolator\u003c\/li\u003e\n\u003cli\u003eLoom\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809457951053,"sku":"SLS-OVL-023-PO","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809457983821,"sku":"SLS-OVL-023-PAF","price":1474.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Dual_Battery_and_Power_Package_f05e2f99-8d2c-49e4-aaef-ca7cb7d9c50e.jpg?v=1790171165"},{"product_id":"discovery-2-dual-battery-and-power-package","title":"Discovery 2 Dual Battery and Power Package","description":"\u003cp\u003eDual Battery and Power Package for the Discovery 2: a DC to DC charger, a lithium leisure battery, isolator and wiring.\u003c\/p\u003e\u003cp\u003eThese are the packages we would build for our own vehicles before a long trip: the parts that fail far from home, the protection that stops a rock ending the journey, and the equipment that makes living out of the vehicle possible. Each one lists its weight, because an expedition vehicle is usually overweight before it has left the country and payload is the thing people forget to check. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: a flat starter battery after a night running a fridge\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a battery tray\u003c\/li\u003e\n\u003cli\u003eTorque: terminals 8 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 18 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDC to DC charger\u003c\/li\u003e\n\u003cli\u003eLithium battery\u003c\/li\u003e\n\u003cli\u003eIsolator\u003c\/li\u003e\n\u003cli\u003eLoom\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809458016589,"sku":"SLS-OVL-024-PO","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809458049357,"sku":"SLS-OVL-024-PAF","price":1524.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Dual_Battery_and_Power_Package_715a438a-b440-49b7-bebc-fe7cefc62fdd.jpg?v=1790171165"},{"product_id":"discovery-1-roof-tent-and-awning-package","title":"Discovery 1 Roof Tent and Awning Package","description":"\u003cp\u003eRoof Tent and Awning Package for the Discovery 1: a hard shell roof tent and a side awning on a load rated roof rack.\u003c\/p\u003e\u003cp\u003eThese are the packages we would build for our own vehicles before a long trip: the parts that fail far from home, the protection that stops a rock ending the journey, and the equipment that makes living out of the vehicle possible. Each one lists its weight, because an expedition vehicle is usually overweight before it has left the country and payload is the thing people forget to check. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: sleeping somewhere without a campsite\u003c\/li\u003e\n\u003cli\u003eLabour time: about 4 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a roof rack rated for dynamic and static loads\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 110 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRoof tent\u003c\/li\u003e\n\u003cli\u003eAwning\u003c\/li\u003e\n\u003cli\u003eMount kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 4 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809459392845,"sku":"SLS-OVL-032-PO","price":2399.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809459425613,"sku":"SLS-OVL-032-PAF","price":3074.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Roof_Tent_and_Awning_Package_fc3663f6-3173-4de2-988c-beef852a01a1.jpg?v=1790171166"},{"product_id":"discovery-2-roof-tent-and-awning-package","title":"Discovery 2 Roof Tent and Awning Package","description":"\u003cp\u003eRoof Tent and Awning Package for the Discovery 2: a hard shell roof tent and a side awning on a load rated roof rack.\u003c\/p\u003e\u003cp\u003eThese are the packages we would build for our own vehicles before a long trip: the parts that fail far from home, the protection that stops a rock ending the journey, and the equipment that makes living out of the vehicle possible. Each one lists its weight, because an expedition vehicle is usually overweight before it has left the country and payload is the thing people forget to check. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Parts and Fitting\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: sleeping somewhere without a campsite\u003c\/li\u003e\n\u003cli\u003eLabour time: about 4 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a roof rack rated for dynamic and static loads\u003c\/li\u003e\n\u003cli\u003eTorque: to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 110 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRoof tent\u003c\/li\u003e\n\u003cli\u003eAwning\u003c\/li\u003e\n\u003cli\u003eMount kit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 4 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Parts and Fitting is the parts fitted at our workshop, road tested and with the warranty covering labour as well as parts.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809459687757,"sku":"SLS-OVL-033-PO","price":2499.0,"currency_code":"GBP","in_stock":true},{"title":"Parts and Fitting","offer_id":54809459720525,"sku":"SLS-OVL-033-PAF","price":3199.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Roof_Tent_and_Awning_Package_79c8f510-367c-4cca-8c3e-ba703164dd7f.jpg?v=1790171166"},{"product_id":"discovery-1-two-inch-lift-kit-with-fitting","title":"Discovery 1 Two Inch Lift Kit with Fitting","description":"\u003cp\u003eTwo Inch Lift Kit with Fitting for the Discovery 1: springs, dampers, extended brake hoses, caster correction and fitting with alignment.\u003c\/p\u003e\u003cp\u003eA modest lift gives clearance for larger tyres and better approach and departure angles. Too much lift, or a lift without the matching parts, gives worse handling, worn joints and propshaft vibration. Our kits are the height we would run ourselves, with the parts that height actually needs, and we say plainly what changes on the road. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Fitted With Alignment\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: insufficient clearance for larger tyres\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: insurer notification and a headlamp aim\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 70 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFour springs\u003c\/li\u003e\n\u003cli\u003eFour dampers\u003c\/li\u003e\n\u003cli\u003eBrake hoses\u003c\/li\u003e\n\u003cli\u003eCaster correction\u003c\/li\u003e\n\u003cli\u003eAlignment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Fitted With Alignment is fitted at our workshop with a four wheel alignment and headlamp aim afterwards, which a raised or modified vehicle needs.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809460834637,"sku":"SLS-LFT-004-PO","price":1349.0,"currency_code":"GBP","in_stock":true},{"title":"Fitted With Alignment","offer_id":54809460867405,"sku":"SLS-LFT-004-FWA","price":1824.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Two_Inch_Lift_Kit_with_Fitting_6bb9151c-c250-4e7e-80c3-bf09848944d0.jpg?v=1790171167"},{"product_id":"discovery-2-two-inch-lift-kit-with-fitting","title":"Discovery 2 Two Inch Lift Kit with Fitting","description":"\u003cp\u003eTwo Inch Lift Kit with Fitting for the Discovery 2: springs, dampers, extended brake hoses, caster correction and fitting with alignment.\u003c\/p\u003e\u003cp\u003eA modest lift gives clearance for larger tyres and better approach and departure angles. Too much lift, or a lift without the matching parts, gives worse handling, worn joints and propshaft vibration. Our kits are the height we would run ourselves, with the parts that height actually needs, and we say plainly what changes on the road. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Fitted With Alignment\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: insufficient clearance for larger tyres\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: insurer notification and a headlamp aim\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 70 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFour springs\u003c\/li\u003e\n\u003cli\u003eFour dampers\u003c\/li\u003e\n\u003cli\u003eBrake hoses\u003c\/li\u003e\n\u003cli\u003eCaster correction\u003c\/li\u003e\n\u003cli\u003eAlignment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Fitted With Alignment is fitted at our workshop with a four wheel alignment and headlamp aim afterwards, which a raised or modified vehicle needs.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809460900173,"sku":"SLS-LFT-005-PO","price":1399.0,"currency_code":"GBP","in_stock":true},{"title":"Fitted With Alignment","offer_id":54809460932941,"sku":"SLS-LFT-005-FWA","price":1899.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Two_Inch_Lift_Kit_with_Fitting_33259077-dae7-47bc-bafe-071433037232.jpg?v=1790171167"},{"product_id":"discovery-1-heavy-duty-suspension-package","title":"Discovery 1 Heavy Duty Suspension Package","description":"\u003cp\u003eHeavy Duty Suspension Package for the Discovery 1: heavy duty springs and dampers rated for a permanently loaded vehicle.\u003c\/p\u003e\u003cp\u003eA modest lift gives clearance for larger tyres and better approach and departure angles. Too much lift, or a lift without the matching parts, gives worse handling, worn joints and propshaft vibration. Our kits are the height we would run ourselves, with the parts that height actually needs, and we say plainly what changes on the road. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Fitted With Alignment\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: sagging rear, wallowing and bottoming out under load\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: an alignment\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSprings\u003c\/li\u003e\n\u003cli\u003eDampers\u003c\/li\u003e\n\u003cli\u003eBushes\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Fitted With Alignment is fitted at our workshop with a four wheel alignment and headlamp aim afterwards, which a raised or modified vehicle needs.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809461260621,"sku":"SLS-LFT-010-PO","price":1149.0,"currency_code":"GBP","in_stock":true},{"title":"Fitted With Alignment","offer_id":54809461293389,"sku":"SLS-LFT-010-FWA","price":1549.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Heavy_Duty_Suspension_Package_748e7cbe-e8a7-45b2-9455-c523b19061cf.jpg?v=1790171212"},{"product_id":"discovery-2-heavy-duty-suspension-package","title":"Discovery 2 Heavy Duty Suspension Package","description":"\u003cp\u003eHeavy Duty Suspension Package for the Discovery 2: heavy duty springs and dampers rated for a permanently loaded vehicle.\u003c\/p\u003e\u003cp\u003eA modest lift gives clearance for larger tyres and better approach and departure angles. Too much lift, or a lift without the matching parts, gives worse handling, worn joints and propshaft vibration. Our kits are the height we would run ourselves, with the parts that height actually needs, and we say plainly what changes on the road. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Parts Only or Fitted With Alignment\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: sagging rear, wallowing and bottoming out under load\u003c\/li\u003e\n\u003cli\u003eLabour time: about 5 hours, included\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: an alignment\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSprings\u003c\/li\u003e\n\u003cli\u003eDampers\u003c\/li\u003e\n\u003cli\u003eBushes\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 5 hours, included. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eParts Only is the parts delivered to you or your garage, with our fitting notes. Fitted With Alignment is fitted at our workshop with a four wheel alignment and headlamp aim afterwards, which a raised or modified vehicle needs.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Parts Only","offer_id":54809461326157,"sku":"SLS-LFT-011-PO","price":1199.0,"currency_code":"GBP","in_stock":true},{"title":"Fitted With Alignment","offer_id":54809461358925,"sku":"SLS-LFT-011-FWA","price":1624.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Heavy_Duty_Suspension_Package_f1e2f51e-1245-4b78-ad86-6bd6224948a9.jpg?v=1790171212"},{"product_id":"discovery-1-two-inch-lift-kit","title":"Discovery 1 Two Inch Lift Kit","description":"\u003cp\u003eTwo Inch Lift Kit for the Discovery 1: springs, dampers and extended brake hoses for a two inch lift.\u003c\/p\u003e\u003cp\u003eA modest lift gives clearance for larger tyres and better approach and departure angles. Too much lift, or a lift without the matching parts, gives worse handling, worn joints and propshaft vibration. Our kits are the height we would run ourselves, with the parts that height actually needs, and we say plainly what changes on the road. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: clearance\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a caster correction and alignment\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSprings\u003c\/li\u003e\n\u003cli\u003eDampers\u003c\/li\u003e\n\u003cli\u003eBrake hoses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809461883213,"sku":"SLS-LFT-016-S","price":719.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809461915981,"sku":"SLS-LFT-016-HD","price":859.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Two_Inch_Lift_Kit_ca665eed-b9a0-4644-9f4a-5cc85f7a05a5.jpg?v=1790171212"},{"product_id":"discovery-2-two-inch-lift-kit","title":"Discovery 2 Two Inch Lift Kit","description":"\u003cp\u003eTwo Inch Lift Kit for the Discovery 2: springs, dampers and extended brake hoses for a two inch lift.\u003c\/p\u003e\u003cp\u003eA modest lift gives clearance for larger tyres and better approach and departure angles. Too much lift, or a lift without the matching parts, gives worse handling, worn joints and propshaft vibration. Our kits are the height we would run ourselves, with the parts that height actually needs, and we say plainly what changes on the road. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: Standard or Heavy Duty\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: clearance\u003c\/li\u003e\n\u003cli\u003eLabour time: about 6 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: a caster correction and alignment\u003c\/li\u003e\n\u003cli\u003eTorque: factory figures\u003c\/li\u003e\n\u003cli\u003eWeight: about 64 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: two years or 24,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSprings\u003c\/li\u003e\n\u003cli\u003eDampers\u003c\/li\u003e\n\u003cli\u003eBrake hoses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 6 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure. Any modification that changes ride height, tyre size, weight or appearance must be declared to your insurer before you drive the vehicle. Raised vehicles need the headlamp aim reset and a four wheel alignment, and the MOT tester will look at both.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eStandard is the standard specification, which is what most vehicles need and what we would quote unless you told us otherwise. Heavy Duty is the heavy duty specification for expedition, towing and commercial use, rated beyond the factory figures.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"Standard","offer_id":54809461948749,"sku":"SLS-LFT-017-S","price":739.0,"currency_code":"GBP","in_stock":true},{"title":"Heavy Duty","offer_id":54809461981517,"sku":"SLS-LFT-017-HD","price":889.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Two_Inch_Lift_Kit_8b26bb97-c79d-4a74-be53-3f2e6f81a65a.jpg?v=1790171213"},{"product_id":"discovery-1-full-service-kit","title":"Discovery 1 Full Service Kit","description":"\u003cp\u003eFull Service Kit for the Discovery 1: oil filter, fuel filter, air filter, cabin filter and the correct engine oil.\u003c\/p\u003e\u003cp\u003eA proper service on one of these vehicles is more than oil and a filter. The fuel filter, the air filter and the swivel, axle and transfer box oils are all on the schedule, and they are the ones that get skipped. Every kit here is matched to the engine and lists exactly what is in the box. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: skipped fuel filters and old oil, which cause most of the problems we see\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: service interval reset with a diagnostic system on vehicles from the Discovery 3 onwards\u003c\/li\u003e\n\u003cli\u003eAlso needed: a sump plug washer, included\u003c\/li\u003e\n\u003cli\u003eTorque: sump plug to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOil filter\u003c\/li\u003e\n\u003cli\u003eFuel filter\u003c\/li\u003e\n\u003cli\u003eAir filter\u003c\/li\u003e\n\u003cli\u003eCabin filter\u003c\/li\u003e\n\u003cli\u003eEngine oil\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809464701261,"sku":"SLS-FIL-005-OS","price":89.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809464734029,"sku":"SLS-FIL-005-GB","price":129.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809464766797,"sku":"SLS-FIL-005-PA","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Full_Service_Kit_f6d71a9b-7490-444d-83c2-2e9ae725459d.jpg?v=1790171214"},{"product_id":"discovery-2-full-service-kit","title":"Discovery 2 Full Service Kit","description":"\u003cp\u003eFull Service Kit for the Discovery 2: oil filter, fuel filter, air filter, cabin filter and the correct engine oil.\u003c\/p\u003e\u003cp\u003eA proper service on one of these vehicles is more than oil and a filter. The fuel filter, the air filter and the swivel, axle and transfer box oils are all on the schedule, and they are the ones that get skipped. Every kit here is matched to the engine and lists exactly what is in the box. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Genuine Boxed or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: skipped fuel filters and old oil, which cause most of the problems we see\u003c\/li\u003e\n\u003cli\u003eLabour time: about 2 hours\u003c\/li\u003e\n\u003cli\u003eCoding: service interval reset with a diagnostic system on vehicles from the Discovery 3 onwards\u003c\/li\u003e\n\u003cli\u003eAlso needed: a sump plug washer, included\u003c\/li\u003e\n\u003cli\u003eTorque: sump plug to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 9 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOil filter\u003c\/li\u003e\n\u003cli\u003eFuel filter\u003c\/li\u003e\n\u003cli\u003eAir filter\u003c\/li\u003e\n\u003cli\u003eCabin filter\u003c\/li\u003e\n\u003cli\u003eEngine oil\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 2 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809464865101,"sku":"SLS-FIL-006-OS","price":94.95,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809464897869,"sku":"SLS-FIL-006-GB","price":134.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809464930637,"sku":"SLS-FIL-006-PA","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Full_Service_Kit_7409fd76-ebec-45c2-b674-54395f17ca6c.jpg?v=1790171214"},{"product_id":"discovery-1-axle-and-transfer-box-oil-kit","title":"Discovery 1 Axle and Transfer Box Oil Kit","description":"\u003cp\u003eAxle and Transfer Box Oil Kit for the Discovery 1: the correct oils for the front and rear axles and the transfer box or PTU.\u003c\/p\u003e\u003cp\u003eA proper service on one of these vehicles is more than oil and a filter. The fuel filter, the air filter and the swivel, axle and transfer box oils are all on the schedule, and they are the ones that get skipped. Every kit here is matched to the engine and lists exactly what is in the box. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: driveline oils nobody has changed since the vehicle was built\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1.5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: drain plug washers\u003c\/li\u003e\n\u003cli\u003eTorque: plugs 30 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 8 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eAxle oils\u003c\/li\u003e\n\u003cli\u003eTransfer box oil\u003c\/li\u003e\n\u003cli\u003eWashers\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1.5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809467814221,"sku":"SLS-FIL-021-OS","price":69.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809467846989,"sku":"SLS-FIL-021-PA","price":54.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Axle_and_Transfer_Box_Oil_Kit_6198accf-1cf1-4815-907f-903ae402780f.jpg?v=1790171215"},{"product_id":"discovery-2-axle-and-transfer-box-oil-kit","title":"Discovery 2 Axle and Transfer Box Oil Kit","description":"\u003cp\u003eAxle and Transfer Box Oil Kit for the Discovery 2: the correct oils for the front and rear axles and the transfer box or PTU.\u003c\/p\u003e\u003cp\u003eA proper service on one of these vehicles is more than oil and a filter. The fuel filter, the air filter and the swivel, axle and transfer box oils are all on the schedule, and they are the ones that get skipped. Every kit here is matched to the engine and lists exactly what is in the box. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Premium Aftermarket\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: driveline oils nobody has changed since the vehicle was built\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1.5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: drain plug washers\u003c\/li\u003e\n\u003cli\u003eTorque: plugs 30 Nm\u003c\/li\u003e\n\u003cli\u003eWeight: about 8 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eAxle oils\u003c\/li\u003e\n\u003cli\u003eTransfer box oil\u003c\/li\u003e\n\u003cli\u003eWashers\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1.5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Premium Aftermarket is a well regarded aftermarket maker that is not the original supplier. Generally good, and we say where the differences are.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809467945293,"sku":"SLS-FIL-022-OS","price":74.95,"currency_code":"GBP","in_stock":true},{"title":"Premium Aftermarket","offer_id":54809467978061,"sku":"SLS-FIL-022-PA","price":54.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Axle_and_Transfer_Box_Oil_Kit_fa09219a-b9bb-429f-bd01-3990d50e895e.jpg?v=1790171215"},{"product_id":"discovery-1-brake-disc-and-pad-kit-front","title":"Discovery 1 Brake Disc and Pad Kit Front","description":"\u003cp\u003eBrake Disc and Pad Kit Front for the Discovery 1: front discs and pads with wear sensors and fitting hardware.\u003c\/p\u003e\u003cp\u003eBrakes on a heavy vehicle that tows and goes off road work harder than on a car of the same weight. Every kit states the disc sizes and the caliper fitment, because both changed during production and a brake kit that nearly fits is a wasted afternoon. The Discovery 1 shares its chassis design and drivetrain with the Defender and the Range Rover Classic, and it rusts in the same places.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 1, chassis code LJ\u003c\/li\u003e\n\u003cli\u003eEngine: 200Tdi and 300Tdi diesel, 3.5 and 3.9 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1989 to 1998\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn discs and pads\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1.5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: brake fluid\u003c\/li\u003e\n\u003cli\u003eTorque: caliper carrier to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 22 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTwo discs\u003c\/li\u003e\n\u003cli\u003ePad set\u003c\/li\u003e\n\u003cli\u003eWear sensor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1.5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809469387085,"sku":"SLS-BRK-005-OS","price":179.95,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809469419853,"sku":"SLS-BRK-005-U","price":219.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809469452621,"sku":"SLS-BRK-005-GB","price":249.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_1_Brake_Disc_and_Pad_Kit_Front_9ef1e945-6705-4325-82c3-27ce8cb59a15.jpg?v=1790171263"},{"product_id":"discovery-2-brake-disc-and-pad-kit-front","title":"Discovery 2 Brake Disc and Pad Kit Front","description":"\u003cp\u003eBrake Disc and Pad Kit Front for the Discovery 2: front discs and pads with wear sensors and fitting hardware.\u003c\/p\u003e\u003cp\u003eBrakes on a heavy vehicle that tows and goes off road work harder than on a car of the same weight. Every kit states the disc sizes and the caliper fitment, because both changed during production and a brake kit that nearly fits is a wasted afternoon. The Discovery 2 is the Td5 era, with self levelling rear air on some cars and ACE active roll control on others, and both matter when you order suspension.\u003c\/p\u003e\u003ch3\u003eSpecification and fitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFits: Discovery 2, chassis code L318\u003c\/li\u003e\n\u003cli\u003eEngine: Td5 diesel and 4.0 V8\u003c\/li\u003e\n\u003cli\u003eProduction dates: 1998 to 2004\u003c\/li\u003e\n\u003cli\u003eQuality: OE Supplier or Uprated or Genuine Boxed\u003c\/li\u003e\n\u003cli\u003ePart number: cross referenced to the factory part number for your VIN and confirmed before dispatch, because supersessions on these vehicles are frequent and one printed number would be wrong for somebody\u003c\/li\u003e\n\u003cli\u003eThe failure this addresses: worn discs and pads\u003c\/li\u003e\n\u003cli\u003eLabour time: about 1.5 hours\u003c\/li\u003e\n\u003cli\u003eCoding: none required. Fit it and drive\u003c\/li\u003e\n\u003cli\u003eAlso needed: brake fluid\u003c\/li\u003e\n\u003cli\u003eTorque: caliper carrier to spec\u003c\/li\u003e\n\u003cli\u003eWeight: about 22 kg\u003c\/li\u003e\n\u003cli\u003eWarranty: one year or 12,000 miles, whichever comes first\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat arrives\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTwo discs\u003c\/li\u003e\n\u003cli\u003ePad set\u003c\/li\u003e\n\u003cli\u003eWear sensor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitting\u003c\/h3\u003e\u003cp\u003eLabour guide: about 1.5 hours. Land Rover changes specification mid production, often by VIN rather than by model year, so send the VIN or the registration with the order and we confirm the part against the build data before anything leaves. It takes two minutes and it is the difference between a part that fits and a return. We are an independent Land Rover specialist and parts supplier. We are not Land Rover or Jaguar Land Rover and are not appointed by them; the model names are their trademarks and are used here to describe fitment. Everything we sell is chosen for vehicles that actually get used: towed with, loaded, driven through water and parked in fields, rather than for the brochure.\u003c\/p\u003e\u003ch3\u003eWhich version to buy\u003c\/h3\u003e\u003cp\u003eOE Supplier is made by the firm that supplies the factory, in its own box rather than a dealer box. Same part, same line, typically 30 to 40 per cent cheaper than the dealer. Uprated is the revised or heavier duty specification, built for vehicles that are loaded, towed with and taken off road rather than parked outside a school. Genuine Boxed is in the manufacturer's own packaging with the manufacturer's number on it. Worth it for warranty work, lease returns or a car with full dealer history, and not otherwise.\u003c\/p\u003e","brand":"Solihull Spares","offers":[{"title":"OE Supplier","offer_id":54809469550925,"sku":"SLS-BRK-006-OS","price":184.95,"currency_code":"GBP","in_stock":true},{"title":"Uprated","offer_id":54809469583693,"sku":"SLS-BRK-006-U","price":229.0,"currency_code":"GBP","in_stock":true},{"title":"Genuine Boxed","offer_id":54809469616461,"sku":"SLS-BRK-006-GB","price":259.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0993\/6247\/2269\/files\/Discovery_2_Brake_Disc_and_Pad_Kit_Front_0ba3f00d-0d83-478d-9152-37f7aa6723a1.jpg?v=1790171263"}],"url":"https:\/\/solihullspares.com\/collections\/discovery-1-2.oembed","provider":"Solihull Spares","version":"1.0","type":"link"}